TASKalfa 3011i Page 498 Operation Manual Download | Manualshive

Page: 498 / 610

background image

10-17

Troubleshooting > Troubleshooting

2 or more sheets are
overlaps when ejected.
(multi feed)

―

Load the paper correctly.

Printouts are wrinkled.

Is the paper loaded correctly?

Load the paper correctly.

―

Turn the orientation 180 degrees
around in which the paper is
positioned.

Is the paper damp?

Replace the paper with new paper.

Printouts are curled.

―

Turn the paper over in the cassette,
or turn the orientation 180 degrees
around in which the paper is
positioned.

Is the paper damp?

Replace the paper with new paper.

Printer driver cannot be
installed.

Is the driver installed with the host
name while Wi-Fi or Wi-Fi Direct
function is available?

Specify the IP address instead of
the host name.

Cannot print.

Is the machine plugged in?

Plug the power cord into an AC
outlet.

―

Is the machine powered on?

Turn on the main power switch.

Are the printer cable and network
cable connected?

Connect the correct printer cable
and network cable securely.

Is the print job paused?

Resume printing.

When the wired or Wi-Fi network is
configured using the name
resolution, does the IP address
(private address) of the other
network which can not access
coexists?

The number of host name and
domain name which can be used
with the machine is one
respectively. Configure the network
under this restriction.

―

Change the settings of name
resolution such as NetBEUI and
DNS, or network environment
settings.

Command
Center RX
User
Guide

Select Wi-Fi, Wired Network or
Optional Network as an unlimited-
use network on Primary Network
(Client).

Set to [

Wired

] or [

Wi-Fi

] either one

of [

On

], and set the other setting to

[

Off

].

Symptom

Checkpoints

Corrective Actions

Reference

Page

«
...
496
497
498
499
500
...
»

Summary of Contents for 3011i



































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 3011i

Brand: Panasonic Pages: 24

Brand: Oki Pages: 40

Workio DP-1820E

Brand: Panasonic Pages: 38

Brand: Samsung Pages: 165

Brand: Samsung Pages: 2

Inkjet SCX-1150F

Brand: Samsung Pages: 66

Brand: Samsung Pages: 155

CLX-3170FN series

Brand: Samsung Pages: 220

CLX 6210FX - Color Laser - All-in-One

Brand: Samsung Pages: 36

CLX-3160 Series

Brand: Samsung Pages: 139

Brand: Samsung Pages: 8

Lazett Combo SCX-4016

Brand: Samsung Pages: 2

Brand: Samsung Pages: 319

Brand: Oki Pages: 2

OKIPAGE 8c Plus

Brand: Oki Pages: 48

Brand: Oki Pages: 257

Brand: Oki Pages: 113

Brand: Oki Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands