background image

©Copyright Task Force Tips LLC 2003-2020

5

LIU-030 August 24, 2020 Rev10

4.0 FLOW CHARACTERISTICS

Figure 4.0A

Figure 4.0B

5.0 FOAM SELECTION

In any eductor type system the accuracy of the foam concentrate to water ratio will depend upon the viscosity (thickness) of the foam

concentrate. The more viscous, or thick, the foam concentrate, the greater the amount of energy required to draw the concentrate into

the eductor. The viscosity of most foam concentrates changes with temperature, with some thickening to a gel at temperatures of 40ºF

(4ºC).
The PRO/pak percentage knob has two sides, the green Class A side was calibrated for 20 Centipoise Class A foam concentrates and 

the red, Class B, side was calibrated with National Foam’s Universal Gold® AFFF concentrate.

Actual foam concentrations may vary with changes in water flow, foam concentrate temperature, and viscosity. The user must verify that 

the performance of the concentrate is suitable for the application. In all cases, follow the concentrate manufacturer’s recommendation.

WARNING

Agent concentrates can be ineffective if not used at the correct concentration ratio. Ineffective 

agents can increase the potential for injury or death. Ensure that the Percentage Knob is set to the 

correct concentration ratio for the type of agent being used prior to flowing. 

0

0

FLOW (GPM)

PRO/pak FLOW CHARACTERISTICS (with valve fully open)

INLET PRES

SURE (PSI)

20

18

2

6

16

14

12

10

4

24 26

22

8

28

50

150

350

250

450

100

300

200

400

500

MAXIMUM OPERATING
PRESSURE = 500 PSI

MINIMUM OPERATING
PRESSURE = 40 PSI

0

0

FLOW (L/MIN)

50

40

30

10

60

20

70

80

100

90

2

6

14

10

18

4

12

8

16

22
20

24

26

28

30

PRO/pak FLOW CHARACTERISTICS (with valve fully open)

MAXIMUM OPERATING PRESSURE = 40 BAR

MINIMUM OPERATING PRESSURE = 3 BAR

INLET PRES

SURE (BAR)

100

MINUTES TO USE 2-1/2 GALLONS OF 

CONCENTRATE AT 12 GPM

PERCENT

MINUTES

0.1

208

0.2

104

0.3

69

0.4

52

0.5

42

1

21

3

7

6

3.5

MINUTES TO USE 10 LITRES OF 

CONCENTRATE AT 45 l/min

PERCENT

MINUTES

0.1

208

0.2

104

0.3

69

0.4

52

0.5

42

1

21

3

7

6

3.5

Summary of Contents for PRO/pak













Reviews: