background image

©Copyright Task Force Tips, Inc. 2011-2012 

LIA-520 April 25, 2011 Rev01

TASK FORCE TIPS, INC.

MADE IN USA • www.tft.com

3701 Innovation Way, Valparaiso, IN 46383-9327 USA

800-348-2686 • 219- 462-6161 • Fax 219-464-7155

8.0 WARRANTY

Task Force Tips, Inc., 3701 Innovation Way, Valparaiso, IN 46383-9327 (*TFT*) warrants to the original purchaser of its Hydrant 
Master (*equipment*), and to anyone to whom  it is transferred, that the equipment shall be free from defects in material and 
workmanship during the fi ve (5) year period from the date of purchase.

TFT’s obligation under this warranty is specifi cally limited to replacing or repairing the equipment (or its parts) which are shown by 
TFT’s examination to be in a defective condition attributable to TFT.  To qualify for this limited warranty, the claimant must return 
the equipment to TFT, at 3701 Innovation Way, Valparaiso, IN 46383-9327, within a reasonable time after discovery of the defect.  
TFT will examine the equipment.  If TFT determines that there is a defect attributable to it, TFT will correct the problem within a 
reasonable time.  If the equipment is covered by this limited warranty, TFT will assume the expenses of repair.

If any defect attributable to TFT under this limited warranty cannot be reasonably cured by repair or replacement, TFT may elect to 
refund the purchase price of the equipment, less reasonable depreciation, in complete discharge of its obligations under this limited 
warranty.  If TFT makes this election, claimant shall return the equipment to TFT free and clear of any liens and encumbrances.

This is a limited warranty.  The original purchaser of the equipment, any person to whom it is transferred, and any person who is 
an intended or unintended benefi ciary of the equipment, shall not be entitled to recover from TFT any consequential or incidental 
damages for injury to person and/or property resulting from any defective equipment manufactured or assembled by TFT.  It is 
agreed and understood that the price stated for the equipment is in part consideration for limiting TFT’s liability.  Some states do 
not allow the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.

TFT shall have no obligation under this warranty if the equipment is, or has been, misused or neglected (including failure to provide 
reasonable maintenance) or if there have been accidents to the equipment or if it has been repaired or altered by someone else.

THIS IS A LIMITED EXPRESS WARRANTY ONLY. TFT EXPRESSLY DISCLAIMS WITH RESPECT TO THE EQUIPMENT 
ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND ALL IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR 
PURPOSE.  THERE IS NO WARRANTY OF ANY NATURE MADE BY TFT BEYOND THAT STATED IN THIS DOCUMENT.

This limited warranty gives you specifi c legal rights, and you may also have other rights which vary from state to state.

7.3 OUTLET COMPONENTS

ID

QTY

DESCRIPTION

4.0" STORZ

5.0" STORZ

6.0" STORZ

4.0" MALE

4.5" MALE

5.0" MALE

53

1

OUTLET MATE

A2115

A2115

A2115

A2115

A2115

A2115

54

1

CUP SEAL

A1597

A1596

A1596

A1596

A1596

A1596

55

1

PLASTIC STRIP

A1292

A1291

A1291

A1291

A1291

A1291

56

1

LOCKOUT SCREW

A1294

A1294

A1294

A1294

A1294

A1294

57

1

OUTLET COUPLING

A4124

A4125

A4126

A4620N

A4625N

A4630N

1

PORT COVER

A1298

--

--

--

--

--

1

PORT PLUG

A1299

A1299

A1299

A1299

A1299

A1299

1

MATE PSM4.25 X PSF5.25

A4730

--

--

--

--

--

1

CUP SEAL

A1596

--

--

--

--

--

1

PLASTIC STRIP

A1291

--

--

--

--

--

Summary of Contents for HYDRANT MASTER

















Reviews: