manualshive.com logo in svg

Task Force Tips 350 Series, Manual

Share
Download
Task Force Tips 350 Series Manual Download Page 1

©Copyright Task Force Tips LLC 2010-2021

1

LIU-360 October 14, 2021 Rev05

TASK FORCE TIPS LLC

MADE IN USA · tft.com 

3701 Innovation Way, Valparaiso, IN 46383-9327 USA

800-348-2686 · 219-462-6161 · Fax 219-464-7155

G-Force

INSTRUCTION FOR INSTALLATION, OPERATION, AND MAINTENANCE

EDUCTOR 

350 SERIES IN-LINE

DANGER

Understand manual before use. Operation of this device without understanding the manual and

receiving proper training is a misuse of this equipment. Obtain safety information at tft.com/

serial-number. 
This equipment is intended for use by trained and qualified emergency services personnel for

firefighting. All personnel using this equipment shall have completed a course of education

approved by the Authority Having Jurisdiction (AHJ).
This instruction manual is intended to familiarize firefighters and maintenance personnel with the

operation, servicing, and safety procedures associated with this product. This manual should be

kept available to all operating and maintenance personnel. 

350

Read manual before use.

WARNING

MODEL

UE-350

GPM

Eductor

®

www.tft.com

800-348-2686

UL611

Inlet 200 psi (14 bar)

Consult Manual for Hoselay 

and Nozzle Selection.

UL601

350 GPM

200 PSI Eductor

Summary of Contents for 350 Series













Reviews:

No comments

Brands by name

Popular brands

Load more brands