Tascam VS-R264 Reference Manual Download

Page: 24 / 28

TASCAM VS-R264 / VS-R265

6 - Specifications

Inputs and outputs

Video inputs and outputs

HDMI IN/OUT ports

Connector: Type A receptacle

Input resolutions

2160p30/p29.97/p25/p24/p23.98 (VS-R265 only), 1080p60/

p59.94/p50/p30/p29.97/p25/p24/p23.98, 720p60/p59.94/

p50, 576p50, 480p60, 480p59.94

Frame rate limiting

On/Off

Encode scaling resolution

Passthrough, 320x180p, 480x270p, 640x360p, 720x480p,

720x576p, 960x540p, 1280x720p, 1920x1080p, 3840x2160p

(VS-R265 only)

Encoding formats

H.264, H.265 (VS-R265 only)

Encoding bit rates

500 kbps - 30 Mbps

Bit rate control

Variable, Constant

Key frame interval

Seconds: 0.25 - 16.5 (default: 1) in 0.25 intervals
Frames: 3 - 1000

Video streaming

Supported protocols*

RTMP, RTSP, HLS, RTP, UDP

* H.265 format streaming only supports RTP and UDP.

Audio inputs and outputs

ANALOG IN connectors (balanced)

Connectors: Euroblock 3.81mm pitch
Nominal input levels:

+4 dBu (1.23 Vrms, when Ref.Level set to other than -9

dBFS)
+6 dBu (1.55 Vrms, when Ref. Level set to -9 dBFS)

Maximum input level (switchable):

+15 dBu (4.36 Vrms, Ref. Level: -9 dBFS)
+18 dBu (6.16 Vrms, Ref. Level: -14 dBFS)
+20 dBu (7.75 Vrms, Ref. Level: -16 dBFS)

Input impedance: 10 kΩ or higher

ANALOG IN connectors (unbalanced)

Connector: 3.5mm (1/8") stereo mini jack
Input impedance: 10 kΩ
Minimum input level: -10 dBV (0.316 Vrms)
Maximum input level: +6 dBV (2.0 Vrms)

ANALOG OUT connectors (balanced)

Connectors: Euroblock 3.81mm pitch
Nominal output levels:

+4 dBu (1.23 Vrms, when Ref.Level set to other than

-9dBFS)
+6 dBu (1.55 Vrms, when Ref. Level set to -9 dBFS)

Maximum output level (switchable):

+15 dBu (4.36 Vrms, Ref.Level: -9 dBFS)
+18 dBu (6.16 Vrms, Ref.Level: -14 dBFS)
+20 dBu (7.75 Vrms, Ref.Level: -16 dBFS)

Output impedance: 200 Ω or lower

ANALOG OUT connectors (unbalanced)

Connector: 3.5mm (1/8") stereo mini jack
Output impedance: 200 Ω
Minimum output level: -10 dBV (0.316 Vrms)
Maximum output level: +6 dBV (2.0 Vrms)

0 dBu=0.775 Vrms

Control input/output

Ethernet/PoE+ connector

Connector: RJ-45
Transmission protocol: TCP/IP, UDP, HTTP
Gigabit Ethernet standard: 1000BASE-T (IEEE 802.3ab)
Cables: category 5e or faster STP cables

USB port

Connector: USB A-type 4-pin
Protocol: USB 3.0

Summary of Contents for VS-R264





























Search results

Summary of Contents for VS-R264

Reviews:

Related manuals for VS-R264

Brands by name

Popular brands

Tascam VS-R264, Reference Manual

Search results

Summary of Contents for VS-R264

Reviews:

Related manuals for VS-R264

Brands by name

Popular brands