1 – Introduction
TASCAM CC-222
MK
IV
17
4 – Disc operations
Playback modes
The unit can be set to play back a single track, the whole
disc in the created order, the tracks of the disc in a random
(shuffled) order, or a programmed order. This operation
takes place when stopped.
NOTE
Selecting the playback mode is only possible using the
remote control unit.
1 When stopped, press the
PLAY MODE
key on the
remote control repeatedly to cycle the display
through the following:
•
Continue.
Normal playback mode. Playback contin-
ues in the normal order.
•
Single.
The currently selected track is played and
then playback stops. The
SINGLE
indicator lights in this
mode.
•
Random.
In this mode, all the tracks on the disc are
played in random order, and the
RANDOM
indicator lights
(see “Random playback” on page 17 below).
•
Program.
The
PROGRAM
indicator lights in this mode
(see “Program playback” on page 17 below).
The selected mode is shown in large characters dis-appears
from the display a few seconds after selecting the mode,
and the display returns to its previous mode.
Program playback
The steps to set up to 99 program steps (tracks) to be
played back in a specified order are as follows:
1 When stopped, press the
PLAY MODE
key until the
display shows
Program
.
2 The display changes to show
0Tr 00:00 00
,
meaning that there are no tracks assigned for pro-
gram playback.
3 Use the number keys on the remote control to enter
a track number. There is no need to press the
EN-
TER
key.
The track entered is assigned to the program step,
and the display changes, showing the track number,
the total time of the program so far, and the step
number, e.g.
2Tr 14:56 03
.
4 The next program step can then be entered.
NOTE
Steps 3 and 4 above can also be carried out from the
main unit by turning and pushing the MULTI DIAL key.
5 Repeat steps 3 and 4 above until the program is
complete.
6 Press the
PLAY
key to start playback at the first
program step.
The display shows the track, the current time dis-
play, and the program step number.
While in program playback mode, using the
SKIP
keys or the
MULTI DIAL
moves backwards and for-
wards in the order set in the program.
Use the
PAUSE
key to stop playback temporarily or the
STOP
key to stop playback of the program. If the
STOP
key is used, when playback is restarted, it starts from the
first program step.
When stopped, if the
CLEAR
key on the remote control is
pressed, it cancels the last track entered in the program.
Clear the program by pressing the
PLAY MODE
until the
display shows
Continue
. The program is also cleared
when the disc tray is opened, and if the
STOP
key is
pressed when playback is stopped in programmed order
mode.
The programmed play order is not memorized when the
power is turned off.
If you enter more than 99 program steps, the message
PGM
Full !
appears on the display.
If the total time programmed goes over 100 minutes, the
message
--:--
appears on the display.
In this mode, the unit will playback all the tracks on the
disc in random order.
1 When stopped, press the
PLAY MODE
key until the
display shows
Random
.
2 Press the
PLAY
key to start random playback.
While playing back, using the track skip function
will move forwards through the random order. Turn
the
MULTI DIAL
on the unit clockwise or press the
SKIP
(
¯
) key on the remote control.
NOTE
You cannot go backwards to previous tracks in the
Random playback mode.
To stop random playback, press the
STOP
key. Opening
the disc tray also stops random playback.
Random playback
