Socket
Screw
杯头内六角螺丝
M5x12mm
Spindle
Bearing
Spacer
横轴轴承垫片
Ø5xØ15x1mm
Spindle
Bearing
Spacer
横轴轴承垫片
Ø8xØ15x2.5mm
Metal Main Rotor Housing
主旋翼固定座
Damper Rubber
横轴橡胶垫圈
Ø7xØ16xØ4.5mm
Feathering Shaft
横轴
Ø8x86mm
Damper Rubber
横轴橡胶垫圈
Ø7xØ16.5xØ4.8mm
O
il
T
4
3
X2
For original manufactory package, if the
product is already assembled by factory,
please check again if screws are firmly
secured and applied with some glue.
原装零件出厂包装如果组装完毕
,
请需再确
认各螺丝是否锁紧上胶。
The feathering shaft and feathering shaft socket screws are wear items , and thus should be inspected for
replacement after every 20 flights. For flights with high head speed , the inspection interval should be reduced
to ensure flight safety.
主旋翼轴承、横轴和横轴螺丝属于飞行消耗品
,
建议每
20
趟定期检查以及更换
,
主轴旋转飞速时
,
请缩短定期检查趟数
,
以确保飞行安全 .
600 ASSEMBLY
SECTION
Apply a little amount of T43 thread lock when
fixing a metal part.
所有螺丝锁紧金属件时请使用适量
T43
（
螺丝胶
）
Socket Screw
台阶内六角螺丝
(M3x7.5mm)
Bearing
轴承
(Ø8xØ16x5mm)x4
Spindle
Bearing Spacer
横轴轴承垫片
(Ø11.5xØ15.8x0.3mm)x2
Thrust Bearing
止推轴承
(Ø8xØ16x5mm)x2
Damper rubber
横轴橡胶垫圈
Ø7xØ16.5xØ4.8mmx4
Damper rubber
横轴橡胶垫圈
Ø7xØ16xØ4.5mmx2
Spindle Bearing Spacer
横轴轴承垫片
Ø11xØ14x1mmx2
Spindle Bearing Spacer
横轴轴承垫片
Ø5xØ15x1mmx2
Socket Screw
内六角螺丝
M5x12mmx2
600 ASSEMBLY
SECTION
Thrust
Bearing
止推轴承
Ø8xØ16x5mm
Spindle
Bearing Spacer
横轴轴承垫片
Ø11.5xØ15.8x0.3mm
Bearing
轴承
Ø8xØ16x5mm
Bearing
轴承
8x 16x5mm
Ø
Ø
Socket
Screw
台阶内六角螺丝
M3x7.5mm
Main
Rotor
Holder
600主旋翼夹座
Main
Rotor
Holder
Arm
600主旋翼夹座臂
T4
3
Oil
T4
3
Thrust Bearing
止推 承
Thrust Bearing
止推 承
Thrust bearing and washer for radial bearing are
wear items , and thus should be inspected for
replacement after every 20 flights. For flights
with high headspeed , the inspection interval
should be reduced to ensure flight safety.
止 推 轴 承 及 横 轴 垫 圈 属 于 飞 行 消 耗 品,建 议
20
趟
定 期 检 查 及 更 换,高 主 旋 翼 转 速 飞 行 时,请 缩 短 定
期 检 查 之 趟 数,以 确 保 飞 行 安 全.
Apply a little amount of T43 thread lock
when fixing a metal part.
所有螺丝锁紧金属件时请使用适量
T43
（
螺丝胶
）
Thrust Bearing
止推轴承
Main Rotor Holder
主旋翼夹座
IN(Larger ID)
(
内径较大
外径较大
)
OUT(Smaller ID)
(
内径
较小 外径较小)
Apply Grease On
Thrust Bearing
止推轴承涂上润滑油
Before installtion the rupper ,please put the rupper in hot water
for 2 minutes.when installing apply the oil first ,then push the
two
to the end, and finally push the other four.
Ø7xØ16xØ4.5mm
橡胶垫圈安装前需要将橡胶垫圈放入热水中浸泡
2
分钟。安装时先
将垫圈整体涂抹
oil
油，再将两颗
推到底，最后
Ø7xØ16xØ4.5mm
把其它四颗推进。
After the T part is installed,
check the symmetry.
零件安装完成后,检查对称性。
O
il
Page 5
Damper rubber
橡胶垫圈
hardness 75° for 3D fly
硬度
75°
为
3D
飞行用
hardness 90° for racing
硬度
90°
为竞赛机用
Can
be
used
together
可搭配使用
R48
