Thank you for purchasing our product.
To ensure safe and proper operation, please read this manual
thoroughly before use.
Overview
The RTR501B, RTR502B, RTR503B and RTR507B are wireless
data loggers designed to measure and record temperature
and humidity.
Recorded data is then automatically collected by the Base Unit
via wireless communication and downloaded for archive and
analysis.
As a Remote Unit, the RTR501B / 502B / 503B / 507B requires a Base
Unit to carry out wireless communication.
(Compatible Base Units: RTR500BC, RTR500BW, RTR-500MBS-A, RTR-
500DC, RTR-500, RTR-500NW/AW)
For the operation and configuration of the Base Unit, refer to
the instruction manual attached to the Base Unit or the RTR500B
Series Help available on T&D Website.
Wireless Thermo Recorder RTR501B / 502B / 503B / 507B is re-
ferred to as the “(data) logger” or “device” in this manual.
tandd.com
© Copyright T&D Corporation. All rights reserved.
2020.09 16508160003
(1st Edition) Printed on recycled paper.
Package Contents
RTR501B
Internal Temp
Sensor
RTR502B
Temp Sensor
TR-5106
(Included)
RTR503B
Temp-Humidity
Sensor
TR-3310 (Included)
RTR507B
High Precision
Temp-Humidity Sensor
SHB -3101 (Included)
Common Accessories
• Lithium Battery LS14250 (or Large Capacity Battery Adaptor Kit RTR-500B1 for L type model)
• Strap (Not included with L type model)
• Manual Set (Warranty Included)
Part Names
Make sure that the sensor is completely
inserted until you hear a “click” sound.
Sensor
Jack
LCD Display
Antenna
Optical
Communication
Port
<Side>
(L type)
<Side>
<Front>
<Back>
Installing the Battery
Recording starts automatically by inserting the battery with the
default or previous settings.
Battery
Cover
Rubber
Packing
Screw
Lithium Battery
Default Settings
Recording Mode
Endless
Recording Interval 10 minutes
Recording Start
Method
Immediate Start
• Make sure to use the proper type and
size screwdriver. (Phillips head #1
screwdriver is recommended.)
• Insert the supplied battery with the
tube attached. When using a CR2 lithi-
um battery, the tube is not necessary.
• Before closing the cover, check the
rubber packing for dust or scratches,
as they can reduce the water resis-
tance of the rubber.
• Be sure to completely close the cover.
Make sure not to over tighten the
screws.
• Appropriate Tightening Torque:
20N·cm to 30N·cm (2Kgf·cm to 3Kgf·cm)
Battery Replacement
When it is time for the battery to be
replaced, a battery warning mark will
appear. Please change the battery as
soon as possible if this mark appears.
If you continue to use the logger without changing the battery, the
current temperature and [bAtt] will be displayed alternately and
wireless communication will stop. (Recording will continue.)
Alternating
Display
• If the battery is further left unchanged, the display will automatically shut
off and all previously recorded data will be lost.
• Although the logger continues to work for a period after the battery has
been removed, leaving the device without a battery until the LCD display
goes blank will cause all recorded data to be lost.
Remote Unit Registration
Using the software of the compatible Base Unit, carry out Remote
Unit Registration via optical or Bluetooth.
Optical Communication
Connect the Base Unit to a PC with a USB cable, and place the data
logger face down to align the communication areas as shown be-
low.
Bluetooth
®
Communication
When the RTR500BW is a Base Unit, it is possible to make Base Unit
and Remote Unit settings from nearby mobile devices using Blue-
tooth.
Wireless Thermo Recorder
RTR501B / 502B / 503B / 507B
User's Manual
