2009.04 16004244230 3rd Edition
RTR-500B1
Large Capacity Battery Pack
About this Product
This product is a Large Capacity Battery Pack especially designed for use with our
RTR-
500
x Series data loggers.
Caution:
If this product is used in combination with any product other than those
specified above, T&D Corporation shall in no manner, whatsoever,
guarantee the operation of this product.
Package Contents
The package contains the following:
Large Capacity Battery Pack
Rubber Packing
Attachment hook
Drying agent
(Silica Gel)
Double-sided
Adhesive Tape
×
1
(for fastening silica gel)
Screw
×２
(extras for fastening back of
main unit)
Specifications
Power
：
Lithium Battery
×１
(LS
26500
)
Battery Life
：
about
2
years and
6
months
（
Monitoring at
1
minute interval=about
20
months
※
1
）
Waterproof Capability
：
Splash proof
Weight
：
about
75
g (including lithium battery)
Operating Temperature
：
-
40
-
80
℃
※
2
Note:
※
1
：
Battery Life varies depending on measuring environment,
recording interval, transmission frequency, and ambient
temperature. The battery life estimated here is calculated using
a new battery under normal operating conditions and in no way
should be understood as a guarantee of battery life.
※
2
：
Operating temperature depends on the specifications for the data
logger being used.
How to Attach
Caution:
If you do not wish to lose the recorded data, please finish this operation
in less than
1
minute from the time that you remove the battery from the
RTR-
500
x Series unit. (We suggest that you download recorded data
before attaching the adaptor. For details about downloading data, see
the User
’
s Manual that comes with the software you are using or the
Base Unit being used for our Thermo Recorder RTR-
500
x Series Data
Loggers.)
1.
Remove the back lid from the RTR-
500
x Series unit, open the unit
and take out the battery.
2.
Attach the double-sided adhesive tape to the back of the drying agent
and fix to the inner side of the RTR-
500
B
1
.
3.
Insert the accompanying lithium battery into the battery pack.
4.
Check the RTR-
500
B
1
rubber packing for abrasions, cuts and dirt. If
the packing is in good condition, insert into the grooves making sure
that it is properly fit.
Caution
:
●
Abrasions or dirt may cause small opening to occur through which water
or other foreign objects can enter and cause damage to the unit.
●
The rubber packing is a special item and is not sold in stores. If it
becomes damaged, please replace it by ordering [Maintenance Set](TR-
00
P
1
) or by ordering a new [Large Capacity Battery Pack Battery Set]
(RTR-
500
B
2
).
5.
Making sure that the
2
electrical wires are in the grooves as in
diagram A (below left), insert A (as in right diagram) into the battery
space of the RTR-
500
x Series unit. Close the case and fasten the
screws.
Caution:
If the electrical wires are not properly in their grooves, the lid
may not completely close. Please make sure that the wires are
in their grooves before continuing.
If no recording settings have been made before carrying out this
operation, recording will begin from the time section A is inserted into
the battery space.
※
If, after inserting section A, nothing appears in the unit's LCD display,
please repeat the steps above and attach again, For details about the
display, see the appropriate user's manual for the RTR-
500
x Series
unit.
6.
If necessary, put on the attachment hook.
A
A
Shimadachi
817
-
1
, Matsumoto, Nagano
390
-
0852
Japan
Tel:+
81
-
263
-
40
-
0131
Fax:+
81
-
263
-
40
-
3152
E-mail: [email protected]
Homepage: http://www.tandd.com/