background image

D 13373.08
NOVEMBER 2007

MPS

Table of  

Contents

TANDBERG 

MPS

  

ADMINISTRATOR GUIDE

 

Dial-In Numbers

The 

Single Dial In Number

 allows the MPS to set up mul-

tiple conferences, in an Ad Hoc manner. This is triggered 
by a user dialling in to a single number. The MPS will then 
provide a set of services that enables a user to:

Create a new conference on the fly

• 

Access an already created conference

• 

Put on hold until a conference is created 

• 

In the Ad Hoc Conferences table Create Passwords, Access 
passwords and desired templates may be specified for a 
each conference.

Note that Static, Personal and Direct Ad Hoc confer-
ences may be accessed, but not created through the 
Single Dial In Number.

Single Dial In Number Menu

Number of Login Attempts

Limits the number of login attempts a user may have to ac-
cess a conference. Enter a number from 

1

 to 

10

.

Waiting Room Timer

When users dials into a conference which is not started the 
users are placed in a virtual waiting room (put on hold). The 
Waiting Room Timer limits the time (in minutes) a user may 
be placed in the waiting room. 
Enter a value between 1 and 60. The default value is 10 
minutes. 

Enter the numbers to be used:
ISDN:

 The ISDN Single Dial In Number must be a valid PRI number of the TANDBERG MPS at hand. 

IP:

 The IP address for Single Dial In Number must be a valid IP address on the TANDBERG MPS System Controller 

Card.

E.164 Alias:

 The E.164 Alias is a numeric H.323 E.164 Single Dial In Number. The TANDBERG MPS must be 

registered to a Gatekeeper.

H.323 ID:

 The H.323 ID is a alphanumeric H.323 ID Single Dial In Number. The TANDBERG MPS must be regis-

tered to a Gatekeeper.

SIP URI:

 The SIP URI is a alphanumeric SIP URI Single Dial In Number. The TANDBERG MPS must be connected to 

a SIP proxy.

Create Password
On:

 If set to On, configure th

Ad Hoc Conferences

 to select templates and set passwords for each conference. 

Off:

 If set to Off, select the Conference Template to be used from the drop down list.

About

Single Dial In Number Menu

Active

To make the configurations for Single Dial In Number 
functionality to take effect the Active setting must be 
set to On.

On:

 Set to On to enable the 

Single Dial In Number

 function-

ality.

Off: 

Set to Off to disable Single Dial In Number functionality.

124

Introduction

Quick 

Setup

Using  

the MPS

System 

Status

System  

Configuration

Installation

Gateway  

Configuration

Technical  

Descriptions

Appendices

Main

MCU  

Configuration

Summary of Contents for Media Processing System MPS 800




















































































































































































Reviews: