background image

Copyright © Codian 2008. All rights reserved. This Getting Started Guide may not 
be copied, photocopied, translated, reproduced, or converted into any electronic or 
machine-readable form in whole or in part without prior written approval of Codian 
Limited.
Codian Limited reserves the right to revise this documentation and to make changes 
in content from time to time without obligation on the part of Codian Limited to 
provide notification of such revision or change.
Codian Limited provides this documentation without warranty, term, or condition 
of any kind, either implied or expressed, including, but not limited to, the implied 
warranties, terms or conditions of merchantability, satisfactory quality, and fitness 
for a particular purpose. Codian Limited may make improvements or changes to the 
product(s) and/or the program(s) described in this documentation at any time.
All other product and company names herein may be trademarks of their respective 
owners.
61-00020-02 rev 01

TANDBERG
Philip Pedersens vei 20
1366 Lysaker
Norway
Telephone: +47 67 125 125
Telefax: +47 67 125 234
Video: +47 67 117 777
E-mail: [email protected]
www.tandberg.com

Summary of Contents for Codian MSE 8321





















Reviews: