Tally Dascom DT-330 User Manual Download Page 42 | Manualshive

Page: 42 / 66

background image

Tally Dascom DT-330

User Guide V1.0

29

3.2 Installing Config Tool

Your printer CD-ROM comes with Tally Dascom Setup Tool. Go to the related folder and run the
setup installer.

1.

Select whether to create a shortcut. Click “Next” to continue.

2.

Click “Install” to continue.

«
...
40
41
42
43
44
...
»

Summary of Contents for DT-330



































































Reviews:

No comments

Related manuals for DT-330

Brand: Dascom Pages: 12

Brand: Dascom Pages: 19

Brand: Dascom Pages: 5

Brand: Panduit Pages: 74

Brand: Tally Pages: 2

Brand: Tally Dascom Pages: 57

Brand: Fenix Pages: 65

Brand: iFactory3D Pages: 39

Brand: QMS Pages: 144

Brand: Canon Pages: 4

7400DT - Phaser Color LED Printer

Brand: Xerox Pages: 20

ECOSYS M8124cidn

Brand: Kyocera Pages: 44

Brand: Oki Pages: 140

Brand: Citizen Pages: 32

WorkCentre PE120i

Brand: Xerox Pages: 8

Brand: Evolis Pages: 45

Brand: Pantum Pages: 155

Brand: Lexmark Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands