Tait TP8135 User Manual Download Page 101 | Manualshive

Page: 101 / 120

background image

101

Low battery warning

Notice

Do not allow a radio battery to fully discharge every time

you use it, or you will shorten the service life of the battery.
When the battery is low, your radio warns you in the following
ways:

■

The battery symbol on the radio display looks empty.

■

The status LED on the radio slowly flashes red.

■

A high-pitched beep sounds.

You should recharge or replace the battery as soon as possible.
When the battery is completely empty, the message

Battery is

flat

appears on the display. The radio emits a long, low-pitched

beep and then stops working. Turn off the radio.

Charging the battery

Charging a battery for the first time

Fully charge a battery before using it for the first time. This will
take up to 2.5 hours.
The red LED stays lit while the battery charges.

Charging a battery

Notice

For best charging performance, switch off the radio

before placing it in the charger (desktop charger or multicharger
only).

1

Desktop charger: Connect the charger to the correct Tait power
adaptor.
Multicharger and vehicle charger: Power on the charger.
Initially, all three LEDs are lit for two seconds.

2

Place just a battery in the charger, or a radio with a battery
attached (desktop charger or multicharger only). There is no
need to remove a belt clip, antenna, or any accessory that is
attached to the accessory connector.

«
...
99
100
101
102
103
...
»

Summary of Contents for TP8135

























































































































Reviews:

No comments

Related manuals for TP8135

Brand: Uniden Pages: 32

Brand: Samsung Pages: 32

Brand: Samsung Pages: 32

Brand: Sungale Pages: 24

Brand: Porter-Cable Pages: 24

Brand: Vidao Pages: 16

Brand: Jam Audio Pages: 2

Brand: Albrecht Audio Pages: 48

Brand: Renkforce Pages: 8

Brand: MAJORITY Pages: 24

Brand: Subaru Pages: 28

Brand: PRESIDENT Pages: 48

X-Tra Talk GXT1000 Series

Brand: Midland Pages: 28

Brand: Whisper Power Pages: 32

GALE FORCE PT8500E

Brand: PENTAGON Pages: 25

Brand: AvaLAN Pages: 9

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands