Taiden hcs-8300 Installation And Operation Manual Download Page 220

Page: 220 / 255

207

Chapter 8 Technical specifications

8.1 System specifications

System performance

Conforms to IEC 60914, the international standard for

congress systems

System environmental conditions

Working conditions fixed/stationary/transportable

Temperature range:

- Transport: -40 °C to +70 °C

- Operating: 0 °C to +45 °C

Max. relative humidity:

< 95% (not condensing)

Safety:

Compliant to EN 60065

EMC emission:

Compliant to EN 55022

EMC immunity:

Compliant to EN 55024

EMC approvals:

CE, FCC

Power harmonic:

Compliant to EN 61000-3-2

Voltage fluctuations and flicker:

Compliant to EN

61000-3-3

Summary of Contents for hcs-8300
































































































































































































































































Search results

Summary of Contents for hcs-8300

Reviews:

Brands by name

Popular brands

Taiden hcs-8300, Installation And Operation Manual

Search results

Summary of Contents for hcs-8300

Reviews:

Brands by name

Popular brands