manualshive.com logo in svg

Taiden hcs-8300, Installation And Operation Manual

Share
Download
Taiden hcs-8300 Installation And Operation Manual Download Page 202

 

 

189 

6.8 HCS-8319                             

HCS-8319  Service  Request  Control  Unit is equipped 

with a 10" LCD touch panel. In cooperation with the 

service request function of the HCS-8338 and HCS-8348 

series Paperless Multimedia  Congress  Terminal,  it  

displays seat information and service request on the 

LCD and enables response to the request. 

 

 

 

 

 

 

 

6.8.1 Functions and instructions 

 

 

Figure 6.8.1.  HCS-8319 Service Request Control Unit 

Figure 6.8.1

：

 

1.  16:9 high resolution touch screen colour video 

display (10.2")

 

2. Power/Function button 

a)  Touch panel in  “power-on” status: switches to 

“power-off” status when pressed. 

b)  Touch panel in  “operation status”: switches to 

“set up interface” when pressed and hold for 6 

seconds or switches to  “exit/standby” state 

when pressed for a short time. 

c)  “Calibration” status: exit without saving when 

pressed. 

3. SD card slot 

  For SD card, supporting maximum 4 G SD card. 

4. Ethernet interface 

  Touch panel connection to the central control 

system’s main unit  via Ethernet interface 

(direct-connected or via SWITCH, HUB), 

achieving wired control functions. 

5 Power slot 

  15 V - 24 V DC input for power supply. 

6. TAINET 

  Reserved. 

7. USB interface 

  For type A USB devices, such as external mouse. 

8. Mini USB interface 

  For uploading program and upgrading user 

interface. 

9. RS-232 interface (reserved) 

 

 

 

 

 

6.8.2 Connection 

Connection refers  to figure 1.1.4b HCS-8338  Series 

Paperless  Multimedia  Congress System connection 

diagram (dual main unit hot spare +  “Closed Loop – 

Daisy Chain” connection). 

 

Summary of Contents for hcs-8300
































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands