background image

 

8

6.    TECHNICAL SPECIFICATIONS    

 
Type of emission :

  

ISM Band – 433.5 6MHz 

 

Code :

 

 

4 differentiated Channels (A, B, C, D)  

 

Radiated Power Output :

  

10 mW 

 

Range :

 

Superior to 2 km under optimal conditions, direct view 

 

Antenna :

  

 

Multiflex 1/4 

 

Timing Impulse Inputs:

 

Open Working contact. Respect the polarities (Black = Ground) 

 

Timing Outputs: 

4 opto-isolated independent output

    

 

  

Precision :

 

Fixed delay of 100ms +/- better than 1/10,000

th

 second. 

 

Signal Transmission Evidence:

  By audible tone (buzzer) and LED (1, 2, 3, 4) 

 

 

Signal Reception Evidence: 

By audible tone (buzzer) and LED (1, 2, 3, 4) 

 

Signal Reception Monitoring : 

By 4  LED’s. Control of the quality of the reception and of 
eventual disturbances. 

 

Battery Condition Monitoring: 

By red LED (POWER)

  

 

 

    

On           ->    well charged

 

 

 

    

Flashing  ->    to be recharged   

 

Power Supply : 

By internal battery (lithium) for the 

transmitter 

and by internal 

rechargeable accumulator for the 

receiver 

 

Charger : 

AC/DC Adapter 

 

100 – 240 VAC / 9VDC – 550 mA 

 

Polarity :  positive at the center of the plug 

 

Autonomy : 

Approximately 3 years for the 

transmitter 

 

 

Approximately 24 Hours for the 

receiver

 at 20°C 

 

Operating Temperature Range:

   -20°C à + 60 °C

 

 

 

 

Mounting: 

By Velcro or Serflex strap 

 

Dimensions & weight 

Transmitter 

  : 100 x 57 x 32 mm / weight of 175 gr. 

 Receiver

         : 100 x 82 x 32 mm / weight of 380 gr. 

 

Guaranty :

 

One year starting from the purchase date 

 
 

The guaranty is null and void under the following conditions: 

-  

Accumulators or battery out of use 

  

-  

Bad maintenance and obvious damages

 

-  

Input or Outputs damaged by bad connection 

-

  If the device was open without factory authorization

 

 

Summary of Contents for HL 610









Reviews: