manualshive.com logo in svg

Tadiran Telecom TGW4 SERIES, User Configuration Manual

Share
Download
Tadiran Telecom TGW4 SERIES User Configuration Manual Download Page 68

User Configuration Manual                                                                                                      TGW4/8 Gateway Series for Aeonix 

 

56                                                                                                                                                                Tadiran Telecom (TTL) L.P. 

2.7.5 White list for Accessing Web and Telnet   

The white list is used to specify the IP addresses from which access to the TGW through Web or Telnet 

are allowed.   

After login, click the 

Advanced > White

 

list

 tab to open the white list configuration interface. 

Figure 2-30 

White List Configuration Interface 

 

 

 

Step 1 

Click 

Add

. 

Step 2 

In the input box, enter IP addresses and types of services and click 

Save

. 

Step 3 

Select 

enable

. 

 

 

 

  This function takes effect after the TGW restarts. 

  The TGW allows a white list of up to 20 entries. 

 

 

 

 

Summary of Contents for TGW4 SERIES















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands