manualshive.com logo in svg

Tadiran Telecom TGW4 SERIES, User Configuration Manual

Share
Download
Tadiran Telecom TGW4 SERIES User Configuration Manual Download Page 51

TGW4/8 Gateway Series for Aeonix                                                                                                      User Configuration Manual                                                                             

 

Tadiran Telecom (TTL) L.P.                                                                                                                                                                39

 

2.5.4 Trunk Characteristics (TGW8-2G) 

Only a gateway with FXO ports can display this interface. 

After login, click the 

Trunk > Advanced

 tab to open the Advanced configuration interface. 

Figure 2-22 

Trunk Characteristics Configuration Interface 

 

 

 

Table 2-16 

Trunk Characteristics Configuration Parameter 

Name 

Description 

Gain to IP 

Adjust the voice volume from the analog trunk. The default is 0 dB.   
Increase the value when the volume received by internal party is low. 
Range: from -3.0 to +9.0 dB. 

Gain to PSTN 

Adjust the voice volume to the analog trunk. The default is -3 dB. 
Increase the value when the volume received by external party is low.   
Range: from -6.0 to +3.0 dB. 

Summary of Contents for TGW4 SERIES















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands