manualshive.com logo in svg

Tadiran Telecom TGW4 SERIES, User Configuration Manual

Share
Download
Tadiran Telecom TGW4 SERIES User Configuration Manual Download Page 29

TGW4/8 Gateway Series for Aeonix                                                                                                      User Configuration Manual                                                                             

 

Tadiran Telecom (TTL) L.P.                                                                                                                                                                17

 

2.3.4 System Configuration 

After login, click the 

Basic

 > 

System

 tab to open the System configuration interface. 

Figure 2-11 

System Configuration Interface 

 

 

Table 2-5 

System Configuration Parameters 

Note: * indicates mandatory parameters for Aeonix. 

Name 

Description 

First digit timer 

If a subscriber does not dial any digit within the specified time by this parameter after 
off-hook, the gateways will prompt to hang up with a busy tone.   
The value must be an integer, and decimal points are not allowed. 
Unit: Seconds; Default value: 15 sec. 

Interdigit timer 

The maximum time interval to dial the next digit.   
After timeout, the gateways will call out with the collected number.   
The value must be an integer, and decimal points are not allowed. 
Unit: Seconds; Default value: 5 sec. 

Complete entry 
timer 

The value must be an integer, and decimal points are not allowed.   
Unit: second; Default value: 2 sec. 

This parameter is used with the "x.T" rule set in dialing rules. For example, there is 
"021.T" in the dialing rules table. When a subscriber has dialed 021 and has not dialed 
the next number within a set time by this parameter (eg. 2 sec), the gateways will 
consider that the subscriber has ended dial-up and call out the dialed number 021. 

* 

Codec 

Codecs supported by the deivce include G729A/20, PCMU/20 and PCMA/20. This 
parameter must be set due to no default value. For details, see  Table 2-6. 
Several encoding methods can be configured in this item at the same time, separated 
with "," in the middle; the gateways will negotiate with the platform in the order from 
front to back when configuring the codec methods.   

For Aeonix 

 Enter the required codecs methods to be supported by the gateway. 

These codecs must be set due to no default value. 

Insert G729 PCMA & PCMU as first codecs. 

Summary of Contents for TGW4 SERIES















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands