manualshive.com logo in svg

Tadiran Telecom FlexSet-IP 280S, User Manual

The Tadiran Telecom FlexSet-IP 280S is a feature-rich and reliable VoIP phone system. Unlock its full potential by downloading the user manual for free from our website, providing you with comprehensive instructions and troubleshooting tips. Take control of your communication effortlessly with this innovative product.

Share
Download
background image

Station Telephony Features

106

FlexSet-IP 280S User Guide

ELA Groups: Exclusive Hold

ELA Groups: Exclusive Hold

As an ELA Group member, you can put your telephone into 

Exclusive

 

Hold

 mode. This ensures that a call you place on hold 

can be retrieved only at the station where Exclusive Hold was originally placed. If Exclusive Hold is cancelled, the call put on 
hold can be retrieved by any other member of the ELA Group, by pressing the flashing 

LINE

 key. The feature can be utilized 

for a specific call or for all calls.

Operating Exclusive Hold for all ELA calls

 1. To 

activate

 Exclusive Hold, press 

[Setup]

  

[ExHold]

.

The message 

EXCLUSIVE HOLD

 is displayed. 

When this feature is activated, a bullet appears next to 

[ExHold]

.

 2. To 

cancel

 Exclusive Hold, press 

[ExHold]

 again.

The message 

NON EXCL. HOLD

 is displayed.

You may override the station Exclusive Hold setting on a call-by-call basis. Exclusive Hold is a toggle feature. Thus, if your 
station is in 

EXCLUSIVE HOLD

 mode, you may remove the Exclusive Hold restriction and allow others to pick up your held 

call; alternatively, if your station is not in 

EXCLUSIVE HOLD

 mode, you may apply Exclusive Hold to a specific call. This 

is done by pressing 

[ExHold]

 during a call before pressing 

HOLD

. Press this key to toggle the feature on and off. This key can be 

pressed as many times as necessary. If your telephone is not in 

Exclusive

 

Hold

 mode for all calls, press 

[ExHold]

 before you 

press 

[Hold]

. Press 

[Hold]

 to place a call into Exclusive Hold. The 

LINE

 on hold will remain steady on at all other FlexSets in the 

ELA Group, and the call will only be retrievable from your station.

Transferring call to a group member (during conversation):

Once Exclusive Hold is defined for your station (all calls) a bullet is displayed next to 

[ExHold]

, even if the key is pressed to 

temporarily override the Exclusive Hold feature. However, when your call is completed the telephone will return to the 
permanent status, as previously defined for all calls. If your telephone is in 

Exclusive

 

Hold

 mode for all calls, press 

[ExHold]

 

before you press 

[Hold]

.

 1. Press 

[Hold]

. The 

LINE

 on hold will flash at all FlexSets in the ELA Group.

 2. Listen for the confirmation tone.
 3. Inform the party to whom you wish to transfer on which line the call is on hold.

Summary of Contents for FlexSet-IP 280S




























































































































































































































































































Reviews:

No comments

Related manuals for FlexSet-IP 280S

Panasonic KX-TG5631 Quick Manual preview
KX-TG5631
Brand: Panasonic Pages: 8
Panasonic KX-TVA50 Subscriber'S Manual preview
KX-TVA50
Brand: Panasonic Pages: 72
Teledex iPhone 200 series Specification Sheet preview
iPhone 200 series
Brand: Teledex Pages: 1
BT FREESTYLE 80 PLUS User Manual preview
FREESTYLE 80 PLUS
Brand: BT Pages: 34
golmar T-740 Plus Quick Manual preview
T-740 Plus
Brand: golmar Pages: 2
Memorex MC4285 Operating Instructions Manual preview
MC4285
Brand: Memorex Pages: 19
AT&T TL76108 User Manual preview
TL76108
Brand: AT&T Pages: 99
Grundig CALIOS 1 User Manual preview
CALIOS 1
Brand: Grundig Pages: 70
ENZER Touch Screen Caller ID Phone User Manual preview
Touch Screen Caller ID Phone
Brand: ENZER Pages: 5
VTech DS6751 Manual preview
DS6751
Brand: VTech Pages: 16
Aiphone TB-10M Installation & Operation Manual preview
TB-10M
Brand: Aiphone Pages: 12
3SIXT SNAP STICK User Manual preview
SNAP STICK
Brand: 3SIXT Pages: 6
Uniden DECT2080 Series Manuel Du Propriétaire preview
DECT2080 Series
Brand: Uniden Pages: 68
Geemarc MyDECT 100 User Manual preview
MyDECT 100
Brand: Geemarc Pages: 72
GE 21825 User Manual preview
21825
Brand: GE Pages: 15
GE 25861GE3 Specifications preview
25861GE3
Brand: GE Pages: 2
GE 25846EE1 Specifications preview
25846EE1
Brand: GE Pages: 2
GE 26977 User Manual preview
26977
Brand: GE Pages: 3

Brands by name

Popular brands

Load more brands