background image

9.2

Test mode

The Test mode gives you the possibility to test the whole machine without an influence of the
accounting.

Display / Touch

Show test image - to adjust the display
Verify touch calibration
Perform touch calibration - 4 point touch calibration

Audio

Test the left and right speaker

PC

Detailed list of all parts of the PC For inspection please check:

CPU temperature (should be not higher than 70

C)

CPU Fan (should not be zero!)

Hard disk temperature (should be not higher than 60

C)

Coin Acceptor

Test the different coin channels

Note Acceptor

Test the different bank note channels

Buttons / Switches / Lamps

Test all buttons, switches and lamps.
If you press on of the game buttons the corresponding lamp will lit.

Mechanical Meters

You can see if the meters are connected and if there are some outstanding ticks.
It is not possible to test the meters because by a test the figure of the meters would not be correct
anymore.

Hopper

Here you can test the hopper by paying out one coin or all coins.
If you leave this menu, the payout will be stopped.
No payout will be counted in this mode.

Page: 25

Summary of Contents for Golden Island Go4Gold















































































Reviews: