background image

EQUIPMENT RECOMMENDED (NOT INCLUDED)

Radio Transmitter

• 

Radio receiver

• 

Batteries for Transmitter

• 

Electronic Speed Control

• 

Steering Servo

• 

Brushless Motor System

• 

Pinion Gear (64 Pitch)

• 

7.4V Li-Po Pack

• 

190mm Body Shell

• 

Touring Car Wheels, Tires and Inserts

• 

TOOLS RECOMMENDED (NOT INCLUDED)

1.5mm, 2.0mm, 3.0mm Allen Wrench

• 

5.0mm, 5.5mm & 7.0mm Hex Socket Wrench

• 

Modelers Craft Knife

• 

Small Cross Head Screw Driver

• 

Turnbuckle Wrench

• 

Calipers/Ruler

• 

Camber Gauge

• 

Battery Strapping Tape

• 

Instant Glue/Thread Lock

• 

Shock Oil

• 

Gear, Diff. Grease, Joint Grease, Gear Diff Oil

• 

Paint (for Bodyshell)

• 

NOTE:

The  Photon  EX  chassis  uses  the  best  available  components.    All 

• 

replacement parts can be purchased from your local hobby or model 

shop.

There  are  2  versions  of  the  Photon  EX  -  Standard  Chassis  and  Stiff 

• 

Chassis.   Ask you local hobby shops for confirming which kit you would 

like to purchase.

This instruction manual contains a blank setup sheet for your own setup 

• 

record.

Enjoy building and driving your Photon EX!!

Do not use your model:

• 

Near real cars, animals, or people that are unaware that an RC car 

1. 

is being driven.

In places where children and people gather

2. 

In limited indoor spaces

3. 

In wet conditions

4. 

In the street

5. 

In areas where loud noises can disturb others such as hospitals and 

6. 

residential areas

At night or anytime your line of sight to the model may be obstructed 

7. 

or impaired in any way.

To prevent any serious personal injury and/or damage to property, please 

be responsible when operating all remote controlled models.

ELECTRICAL PRECAUTIONS

Insulate  any  exposed  electrical  wiring  (using  heat  shrink  tubing  or 

• 

electrical  tape)  to  prevent  dangerous  short  circuits.    Take  maximum 

care  in  wiring,  connecting  and  insulating  cables.    Make  sure  cables 

are always connected securely.  Check connectors for if they become 

loose.  And if so, reconnect them securely.  Never use R/C models with 

damaged  wires.    A  damaged  wire  is  extremely  dangerous,  and  can 

cause short-circuits resulting in fire.

Low  battery  power  will  result  in  loss  of  control.    Loss  of  control  can 

• 

occur  due  to  a  weak  battery  in  either  the  transmitter  or  the  receiver  

Weak  running  battery  may  also  result  in  an  out  of  control  car  if  your 

car’s receiver power is supplied by the running battery.  Stop operation 

immediately if the car starts to slow down.

When not using RC model, always disconnect and remove battery.

• 

Do  not  disassemble  battery  or  cut  battery  cables.    If  the  running 

• 

battery  short-circuits,  approximately  300W  of  electrical  power  can  be 

discharged, leading to fire or burns.  Never disassemble battery or cut 

battery cables.

Use a recommended charger for the receiver and transmitter batteries 

• 

and follow the instructions correctly.  Over-charging, incorrect charging, 

or using inferior chargers can cause the batteries to become dangerously 

hot.    Recharge  battery  when  necessary.  Continual  recharging  may 

damage battery and, in the worst case, could build up heat leading to 

fire.  If battery becomes extremely hot during recharging, please ask 

your local hobby shop for check and/or repair and/or replacement.

Regularly check the charger for potential hazards such as damage to the 

• 

cable, plug, casing or other defects.  Ensure that any damage is rectified 

before using the charger again.  Modifying the charger may cause short-

circuit or overcharging leading to a serious accident.  Therefore do not 

modify the charger.

Always unplug charger when recharging is finished.

• 

Do not recharge battery while battery is still warm. After use, battery 

• 

retains heat.  Wait until it cools down before charging.

Do not allow any metal part to short circuit the receiver batteries or other 

• 

electrical/electronic device on the model.

Immediately stop running if your RC model gets wet as may cause short 

• 

circuit.

Please dispose of batteries responsibly.  Never put batteries into fire.

• 

BEFORE YOU START

The  Photon  EX  is  a  professional  1/10  scale  touring  car  and  should  be 

built  only  by  persons  aged  16  years  or  older  with  previous  experience 

building  and  operating  R/C  model  cars.    This  is  not  a  toy  and  is  not 

intended for use by beginners or by children without direct supervision of a 

responsible, knowledgeable adult.  Read the instruction manual carefully 

before building.

T.O.P. Racing shall not be liable for any loss, injury or damages, whether 

direct, indirect, special, incidental, or consequential, arising from the use, 

misuse, or abuse of this product and/or any product or accessory required 

to operate this product.

GENERAL PRECAUTIONS

This product is not suitable for children under 16 years of age without 

• 

the direct supervision of a knowledgeable adult.

Assemble this kit only in places away from the reach of small children.

• 

First-time builders and users should seek advice from people who have 

• 

building  experience  in  order  to  assemble  the  model  correctly  and  to 

allow the model to reach its performance potential.

Exercise care when using tools and sharp instruments.

• 

Take care when building, as some parts may have sharp edges.

• 

Keep  small  parts  out  of  reach  of  small  children.    Children  must  not 

• 

be allowed to put any parts in their mouth, or pull vinyl bag over their 

head.

Immediately  after  using  your  model,  do  not  touch  equipment  on  the 

• 

model such as the motor and speed controller, because they generate 

high temperatures.  You may seriously burn yourself by touching them.

Follow the operating instructions for the radio equipment at all times.

• 

Do not put fingers or any objects inside rotating and moving parts, as 

• 

this may cause damage or serious injury as your finger, hair, clothes, 

etc. may get caught.

Be sure that your operating frequency is clear before turning on or running 

• 

your model, and never share the same frequency with somebody else at 

the same time.  Ensure that others are aware of the operating frequency 

you are using and when you are using it.

Always turn on your transmitter before turning on the receiver in the car.  

• 

Always turn off the receiver before turning off your transmitter.

Keep  the  wheels  of  the  model  off  the  ground  when  checking  the 

• 

operation of the radio equipment.

Disconnect the battery pack before storing your model.

• 

To prevent any serious personal injury and/or damage to property, be 

• 

responsible when operating all remote controlled models.

The model car is not intended for use on public places and roads or 

• 

areas  where  its  operation  can  conflict  with  or  disrupt  pedestrian  or 

vehicular traffic.

INTRODUCTION

Page 1

Summary of Contents for Photon EX





























Reviews: