T+A PA 2500 R, User Manual

Page: 59 / 70

59
unqualified persons.
immediately disconnect the mains plug at the wall socket, and ask an If the unit
is damaged, or if you suspect that it is not functioning correctly, authorised

specialist workshop to check it.
Over voltage The unit may be damaged by excess voltage in the power supply, the mains
circuit or in aerial systems, as may occur during thunderstorms (lightning
strikes) or due to static discharges.
Special power supply units and excess voltage protectors such as the

'Power Bar' mains distribution panel offer some degree of protection from
damage to equipment due to the hazards described above.
However, if you require absolute security from damage due to excess voltage,
the only solution is to disconnect the unit from the mains power supply and any
aerial systems.
To avoid the risk of damage by overvoltages we recommend to disconnect all
cables from this device and your HiFi system during thunderstorms.
All mains power supply and aerial systems to which the unit is connected must
meet all applicable safety regulations and must be installed by an approved
electrical installer.
Approved usage
 
The device is designed to operate in a temperate climate and altitudes up to
2000 m above sea level. The range of permissible operating temperatures is
+10 … +35°C. This device is designed exclusively for reproducing sound and/or
pictures in the domestic environment. It is to be used in a dry indoor room which
meets all the recommendations stated in these instructions.
Where the equipment is to be used for other purposes, especially in the medical
field or any field in whi
ch safety is an issue, it is essential to establish the unit’s
suitability for this purpose with the manufacturer, and to obtain prior written
approval for this usage.
Approval and conformity
with EC directives In its original condition the unit meets all currently valid European regulations. It
is approved for use as stipulated within the EC.
By attaching the CE symbol to the unit

declares its conformity the EC
directives and the national laws based on those directives. The declaration of
conformity can be downloaded from
www.ta-hifi.com/DoC .
The original, unaltered factory serial number must be present on the outside of
the unit and must be clearly legible! The serial number is a constituent part of
our conformity declaration and therefore of the approval for operation of the
device. The serial numbers on the unit and in the original

documentation
supplied with it (in particular the inspection and guarantee certificates), must not
be removed or modified, and must correspond.
Infringing any of these conditions invalidates

conformity and approval, and
the unit may not be operated within the EC. Improper use of the equipment
makes the user liable to penalty under current EC and national laws.
Any modifications or repairs to the unit, or any other intervention by a workshop
or other third party not authorised by

, invalidates the approval and
operational permit for the equipment. Only genuine

accessories may be
connected to the unit, or such auxiliary devices which are themselves approved
and fulfil all currently valid legal requirements. When used in conjunction with
auxiliary devices or as part of a system this unit may only be used for the
purposes stated in the section
' Approved usage ' .
Disposing of this
product

The only permissible method of disposing of this product is to take it to your
local collection centre for electrical waste.
FCC Information to the
user
(for use in the United States of
America only)
Class B digital device
– instructions:
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different form that to which
the receiver is connected.
-
Consult the dealer or an experienced radio/TV technician for help.