background image

Table 7-2 

Symptoms

Causes 

The fan speed can not be  
changed. 

Check whether the MODE 
indicated on the display is 
"AUTO" 

Check whether the MODE 
indicated on the display is 
"DRY" 

When the automatic mode is 
selected, the air conditioner will 
automatically change the fan 

speed. 

When dry operation is selected, 
the air conditioner automatically 
change the fan speed. The fan  
speed can be selected during 
"COOL" , "FAN ONLY",  and  "HEAT". 

The remote controller signal is  
not transmitted even when  
the ON/OFF button is pushed. 

Check whether the batteries 
in the remote controller are 
exhausted. 

The power supply is off. 

No receiving tone sounds 
from the indoor unit even 
when the ON/OFF button is 
pressed. 

Check whether the signal 
transmitter of the remote 
controller is properly directed 

to the infrared signal receiver 
of the indoor unit when the  
ON/OFF button is pressed. 

Directly transmit the signal transmitter 
of the remote controller to the infrared 
signal receiver of the indoor unit, and 
then repeatly push the ON/OFF button 
twice. 

The indication on the display 
disappears after a lapse of 
time. 

Check whether the timer 
operation has come to an 
end when the TIMER OFF 

is indicated on the display. 

The air conditioner operation will 
stop up to the set time.  

The TIMER ON indicator  
goes off after a lapse of  
certain time. 

Check whether the timer 
operation is started when 
the 

TIMER ON

 is indicated 

on the display. 

  
Up to the set time, the air conditioner  
will automatically start and the  
appropriate indicator will go off.    

The TEMP. indicator does  
not come on.  

Check whether the MODE  
indicated on the display is 

FAN ONLY 

The temperature cannot be set during  
FAN mode. 

 

Solution 

7.2      Troubles and causes of remote controller 

7.3      Fault information and code 

Before asking for serving or repairing, check the following points.

(See in Table 7-2) 

Fault information is only applicable for the indoor units with panel,and only the panel with digit displays will show 
the fault code,otherwise just four LED lamps. 

The fault indication of LED and digit displays see the following form. 

  

owner’s manual 

15 

Summary of Contents for VRF series



















Reviews: