SystemAir SysAer SR105 Regulation Manual Download Page 37

Page: 37 / 62

English

Done

Com

Scheduler

Archive

1/4

Full>Wait 2m for Restart

Execute

1/3

Execute

1/2

Readwrite

BSP load

a-snapshot sa.-> SD

Sett. service save

Sett. factory load

Sett. service load

Restart required !

Filter

+Settings load <- SD

Settings save-> SD

SD-Card

1/10

Save / load

0.0 h

-Reversing valve

Compressor

1/3

Operation hours

Save / load

Operation hours

1/2

Service

Access

Services

Commissioning

Status

1/4

Main Menu

Done

Com

Scheduler

Archive

1/4

Full>Wait 2m for Restart

Execute

1/3

Execute

1/2

Readwrite

BSP load

a-snapshot sa.-> SD

Sett. service save

Sett. factory load

Sett. service load

Restart required !

Filter

+Settings load <- SD

Settings save-> SD

SD-Card

1/10

Save / load

0.0 h

-Reversing valve

Compressor

1/3

Operation hours

Save / load

Operation hours

1/2

Service

Access

Services

Commissioning

Status

1/4

Main Menu

Done

Com

Scheduler

Archive

1/4

Full>Wait 2m for Restart

Execute

1/3

Execute

1/2

Readwrite

BSP load

a-snapshot sa.-> SD

Sett. service save

Sett. factory load

Sett. service load

Restart required !

Filter

+Settings load <- SD

Settings save-> SD

SD-Card

1/10

Save / load

0.0 h

-Reversing valve

Compressor

1/3

Operation hours

Save / load

Operation hours

1/2

Service

Access

Services

Commissioning

Status

1/4

Main Menu

SysAer

7.9. SERVICE MENU

Limited access with the "Maintenance" profile.

7.9.1. OPERATION TIME

On this screen is used to view:

for each compressor

the operation time

the number of cycles

for each reversing valve

the operation time.

7.9.2. SAVE / LOAD

The Save/Load menu is used to manage the parametering of the unit

SD-Card

indicates if an SD card is in the controller and its state : read/write or read only

Setting save-> SD

: save the curent parameter file on the SD-Card

Setting load<- SD

: Replace the current unit

parametring with the parameter fil of the SD-Card

Filter

: Indicates the files which have not to be

saved on the SD-card

Sett.service load

: Load the parameters which

have been saved previously with the Sett.factory

save menu

Sett.factory load

: Load the parameters of the unit

when delivered by the factory

Sett.service save

: Save the current parameter of

the unit on the controller

a-snapshot sa.-> SD

Saves the alarms to the SD card

BSP load

: Updates the Bios

Summary of Contents for SysAer SR105































































Search results

Summary of Contents for SysAer SR105

Reviews:

Related manuals for SysAer SR105

Brands by name

Popular brands

SystemAir SysAer SR105, Regulation Manual

Search results

Summary of Contents for SysAer SR105

Reviews:

Related manuals for SysAer SR105

Brands by name

Popular brands