D200-309-00
I56-4267-002
Pittway Tecnologica S.r.l. Via Caboto 19/3, 34147 TRIESTE, Italy
DESCRIPTION
The M211E-RF radio input-output module is a battery operated RF
device designed for use with the M200G-RF radio gateway, running
on an addressable fire system (using a compatible proprietary
communication protocol).
It is a dual module having separate input and output capability,
combined with a wireless RF transceiver and is supplied with a
wireless back box.
This device conforms to EN54-18 and EN54-25. It complies with the
requirements of 2014/53/EU for conformance with the RED directive.
SPECIFICATIONS
Supply Voltage:
3.3 V Direct Current max.
Standby Current:
122 µA@ 3V (typical in normal operating mode)
Red LED Current Max: 2 mA
Green LED Cur. Max: 5.5 mA
Re-Sync Time:
35s (max time to normal RF communication from
device power on)
Batteries:
4 X Duracell Ultra123 or Panasonic Industrial 123
Battery Life:
4 years @ 25
o
C
Radio Frequency:
865-870 MHz. Channel width: 250kHz
RF Output Power:
14dBm (max)
Range:
500m (typ. in free air)
Relative Humidity:
5% to 95% (non-condensing)
Terminal Wire Size:
0.5 - 2.5 mm
2
IP Rating:
IP20
Input Module
End-of-Line Resistor: 47K
Supervision Current: 34 µA typical
Output Module
End-of-Line Resistor: 47K
Supervision Current: 60 µA typical
Relay Contacts:
2 A @ 30 VDC (resistive load)
External Power Supply Unit
Voltage:
30V DC max. 8V DC min.
Supervision Fault Voltage: 7V DC typical
INSTALLATION
This equipment and any associated work must be installed in
accordance with all relevant codes and regulations.
Figure 1
details the dimensions of the back box and cover.
Spacing between radio system devices must be a minimum of 1m
Table 1
shows the wiring configuration of the module.
M211E-RF
RADIO SYSTEM INPUT / OUTPUT MODULE
INSTALLATION INSTRUCTIONS
E N G L I S H
Figure 1: IO back box outside dimensions
Table 1: Terminal Connections
-20°C
60°C
+
=
317 g
(66 g)
251 g
I 56- 4267- 002
7.53
125
mm
125 mm
58
mm
Figure 2: Diode Polarity
Load -VE
Load +VE
Input Module
requires 47K EOL for normal operation.
Output Module
requires 47K EOL at the load for normal
operation in supervised mode.
If the load is a low impedance (compared to the EOL) a
series diode should be added for correct load supervision
(see
Figure 2
for diode polarity).
PARTS LIST
Module unit
1
SMB500 back box
1
Front cover
1
Batteries (Duracell Ultra 123 or Panasonic Industrial 123) 4
Back box fixing screws and wall plugs
2
Module fixing screws
2
3-pin terminal block
2
2-pin terminal block
1
47 k-ohm EOL resistor
2
18 k-ohm alarm resistor
1
Module installation instructions
1
SMB500 back box installation instructions
1
TERMINAL
1
2
Output module (Supervised mode) Output module (Relay mode)
3
Connect to T8
Relay NO (normally open)
4
To load +ve
Relay C (common)
5
Connect to T7
Relay NC (normally closed)
6
Supervision: connect to load -ve
Not used
7
To ext PSU –ve
Not used
8
To ext PSU +ve
Not used
Input Module
Input -ve
Input +ve
CONNECTION / FUNCTION