manualshive.com logo in svg

Synthes Anspach, Instructions For Use Manual, Page: 34 / 46

Share
Download
Synthes Anspach Instructions For Use Manual Download Page 34

Sagittal Saw

Electric High Power Sagittal Saw

E-SAGITTAL          High Power e-Sagittal Saw

The Electric High Power Sagittal Saw is compatible with the
SC2000, SC2000U, SC2101, and SC2102 consoles. Refer to
eMax 2 and eMax 2 Plus Operating Instructions section of
this manual.

1. Connect the Electric Sagittal Saw control cable to the

proximal end of the saw attachment. Align the red dots
on the connectors and gently push the cable connector
into the saw connector until fully inserted.

2. The saw may be connected to either handpiece connector

port on the console. Hold connector with red dot at the
top of the connector. Gently push the cable connector
into the handpiece connector port until fully inserted.

3. Depress the handpiece icon button on the console display

until the desired handpiece port is indicated as active.

4. To remove the cable from the Sagittal Saw and console,

grasp ridged portion of connector between thumb and
forefinger of one hand. Gently pull the connector away
from the console (or saw). The connector should remove
easily. If not, ensure only the ridged portion of the con-
nector is pulled. Do not pull on the smooth part of the
connector as this will result in damage to the cable.

Note:

The Foot Control must be connected to the System

Console. See Foot Control Operating Instructions in the
eMax 2 and eMax 2 Plus section of this manual.

Saw Blade Assembly

1. Raise and fully extend the extension handle on the saw

blade attachment mechanism.

2. Rotate the extension handle counterclockwise to open the

saw blade mounting plates.

3. Insert the saw blade into the opening and align the saw

hub with the locking pins in the mounting plates. The
blades can be aligned in 45° increments.

4. Rotate the extension handle clockwise to secure the saw

blade and lower the handle into its closed position.

Note:

Saw blades used must be Synthes Anspach blades.

Warning:

All microSaw blades are for single use only. 

Note: 

Electric High Power Sagittal Saw is now fully

 functional.

                                                                                                                             Anspach Electric Systems

Instructions for Use

      Synthes

         33

0x6.001.507_AD  13.06.14  11:12  Seite 33

Summary of Contents for Anspach















































Reviews:

No comments