manualshive.com logo in svg

Synthes Anspach, Instructions For Use Manual, Page: 33 / 46

Share
Download
Synthes Anspach Instructions For Use Manual Download Page 33

SA-JACOBS

SA-JLATCH

J-Latch and Jacobs Chuck Small Attachments Assembly 

E12                  e12 Electric Handpiece
DRIVER             Keyless Driver
SA-JLATCH       Small Attachment, J-Latch
SA-JACOBS      Small Attachments, Jacobs Chuck

Note:

Anspach does not supply dissection tools for 

SA-JLATCH or SA-JACOBS small attachments. 

Keyless driver refers to DRIVER. 

1. Insert attachment drive shaft into distal end of keyless

driver or distal end of e12 handpiece. Rotate until three
tabs on attachment engage three slots in keyless driver or
e12 handpiece.

2. Continue to rotate counterclockwise while pushing

attach ment into keyless driver or e12 handpiece until
attach ment locks into position and release ring snaps into
position. 

3. When fully engaged, contours on keyless driver body or

e12 handpiece, release ring, and small attachment will be
in alignment.

J-Latch Dissection Tool Assembly

1. Pull back distal sleeve in direction of arrow  on 

SA-JLATCH attachment and hold it down to insert 
dissection tool into distal end of attachment. 

2. Rotate dissection tool slowly until fully seated.
3. Release distal sleeve and check security of dissection tool

by pulling distally on dissection tool.

4. Dissection tool and attachment are secure.  

J-Latch Dissection Tool Removal

1. Pull back distal sleeve in the direction of arrow  on 

SA-JLATCH and hold it down while pulling dissection tool
out distally for removal.

2. Release the distal sleeve.

Keyless Jacobs Chuck Dissection Tool Assembly 

1. Press down on center 

of release button located on 

SA-JACOBS attachment while rotating knurled knob
on attachment clockwise until fully opened.

2. Insert dissection tool into distal end of attachment until it

touches bottom.

3. Rotate knurled knob counterclockwise while centering

 dissection tool on attachment until tight; release button.

4. Check security of dissection tool by pulling distally on

 dissection tool.

5. Dissection tool and attachment are secure.

Caution: 

Do not press down on release button while attach -

ment is in use.

Keyless Jacobs Chuck Dissection Tool Removal

1. Press down on center 

of release button located on 

SA-JACOBS attachment while rotating knurled knob
on attachment clockwise until fully opened.

2. Pull dissection tool out distally for removal.
3. Release button.

Disassembly

microSaw and Small Attachment Removal

1. With one hand supporting attachment, rotate release ring

on keyless driver or e12 handpiece with other hand
counter clockwise until attachment is released.

microSaws and Small Attachments Assembly

32         

Synthes

      Anspach Electric Systems

Instructions for Use

0x6.001.507_AD  13.06.14  11:12  Seite 32

Summary of Contents for Anspach















































Reviews:

No comments