manualshive.com logo in svg

Synthes Anspach, Instructions For Use Manual, Page: 31 / 46

Share
Download
Synthes Anspach Instructions For Use Manual Download Page 31

The microSaws were designed for small bone dissection.
The microSaw Driver provides direct connection to all
Anspach electric handpiece systems. The Driver also enables
rapid exchange of saw head styles through a unique quick-
disconnect system.

Keyless Driver Installation

DRIVER                 Keyless Driver

Note:

Instructions are written such that distal end of hand-

piece and attachment are pointed away from user.

Keyless Driver Installation 

1. Ensure knurled knob on handpiece is in “RUN” (

) posi-

tion.

2. Insert drive shaft of keyless driver into handpiece and ro-

tate clockwise until locked. Gently twist back and forth to
ensure it is locked into position.

eMax Keyless Driver Removal (DRIVER)

1. Move handpiece knurled knob to “SAFE” position.
2. Rotate DRIVER counterclockwise and remove.

DRIVER Duty Cycle 
30 Sec ON, 30 Sec OFF for 8 cycles.
The recommendations for times of use for the DRIVER at-
tachments have been determined under average load and
worst case ambient air temperature of 85 °F (29 °C).

DRIVER

microSaws and Small Attachments
Assembly

30         

Synthes

      Anspach Electric Systems

Instructions for Use

0x6.001.507_AD  13.06.14  11:12  Seite 30

Summary of Contents for Anspach















































Reviews:

No comments