manualshive.com logo in svg

Synthes Anspach, Instructions For Use Manual, Page: 29 / 46

Share
Download
Synthes Anspach Instructions For Use Manual Download Page 29

Bearing Sleeve and Dissection Tool Assembly 
(20° Angle Driver or Straight Driver)

MA-10S        Bearing Sleeve, 10 cm Straight
MA-10C        Bearing Sleeve, 10 cm Curved
MA-15S        Bearing Sleeve, 15 cm Straight
MA-15C        Bearing Sleeve, 15 cm Curved
MA-15ST      Bearing Sleeve, 15 cm Straight Taper
MA-19ST      Bearing Sleeve, 19 cm Straight Taper

1. Rotate knurled knob on driver to line up arrow with

“TUBE”.

2. Fully insert desired bearing sleeve into distal end of driver

by lining up black line on bearing sleeve with black line
on driver. 

3. Rotate knurled knob to line up arrow with “CUTTER”.

Check security of bearing sleeve by pulling distally.

4. Insert dissection tool into distal tip of bearing sleeve.

 Rotate dissection tool slowly until it is fully seated. Rotate
knurled knob on driver to line arrow with “RUN”.

Note:

Additional force is required to seat dissection tool into

curved bearing sleeve.

5. Check security of dissection tool by pulling distally on

 dissection tool head.

6. Bearing sleeve and dissection tool are secure.

Dissection Tool Disassembly

1. Rotate knurled knob on driver to line up arrow with

 “CUTTER”. Remove dissection tool from distal end of
attach ment.

Bearing Sleeve Adjustment

1. Rotate knurled knob on driver to line up arrow with

 “ADJUST”. 

2. Pull bearing sleeve either 3 mm distally or proximally to

 desired exposure. 

3. Rotate knurled knob on driver to line up arrow with “RUN”. 

Bearing Sleeve Disassembly

1. Rotate knurled knob on driver to line up arrow with

“TUBE”. Remove bearing sleeve distal end of driver.

28         

Synthes

      Anspach Electric Systems

Instructions for Use

Minimal Access Attachment and Dissection Tool Assembly

0x6.001.507_AD  13.06.14  11:12  Seite 28

Summary of Contents for Anspach















































Reviews:

No comments