manualshive.com logo in svg

Synthes Anspach, Instructions For Use Manual, Page: 28 / 46

Share
Download
Synthes Anspach Instructions For Use Manual Download Page 28

Note:

Instructions are the same for straight or angled drivers

and for straight or curved bearing sleeves in both 10 cm and
15 cm lengths. The four words labeled on the drivers mean
the following:

CUTTER

– Insert or remove dissection tool.

RUN

– Attachment and dissection tool are now functional.

ADJUST

– Bearing Sleeve can be moved 3 mm forward 

or back.

TUBE

– Insert or remove bearing sleeve.

Warning:

The Minimal Access Attachments are to be used

only for bone dissection applications. Excessive force or side
loads during use can cause rapid temperature increase at the
distal end of the attachment. Always use copious irrigation
with this attachment.

Driver Installation

MA-D20             20° Angle Driver
MA-DRIVER        Minimal Access Straight Driver

Note:

Instructions are written such that distal end of hand-

piece and attachment are pointed away from user.

eMax Driver Installation

1. Ensure handpiece knurled knob is in “RUN” (

) position.

2. Insert drive shaft of driver into distal end of handpiece,

push and rotate to right until it stops. Listen for a click as
handpiece knurled knob moves up to seat next to driver.

3. Gently twist back and forth to ensure driver is locked into

position.

MA-D20

MA-DRIVER

Minimal Access Attachment and
Dissection Tool Assembly

                                                                                                                             Anspach Electric Systems

Instructions for Use

      Synthes

         27

0x6.001.507_AD  13.06.14  11:12  Seite 27

Summary of Contents for Anspach















































Reviews:

No comments