manualshive.com logo in svg

Synthes Anspach, Instructions For Use Manual, Page: 18 / 46

Share
Download
Synthes Anspach Instructions For Use Manual Download Page 18

Irrigation 
(Activate and Deactivate)

Decrease Flow

LED: Irrigation 
Flow Rate

Increase Flow 

Irrigation Pump
Release Button

Irrigation Pump

Optional Irrigation Assembly and Operation 
(Excludes SC2102)

1. Upon start-up Irrigation is OFF. LED is not illuminated.
2. Depress the button located on the right side of the

 console to eject pump head.

3. Insert IV pole into bracket on back of console.
4. Hang irrigation bag onto IV Pole.
5. To activate, depress the “Irrigation” button on the face

panel. LED illuminates. 

6. To control flow of irrigation, depress arrows located to

right of irrigation button on face panel.

7. Irrigation can also be activated from certain optional Foot

Controls (see Step 5 of Foot Control Operation). Depress
Irrigation Control Switch on top right of the foot control.
Upon activation, LED on face panel illuminates.

Irrigation Tubing Set-up

IRRIGATE-TUBE            Sterile Tubing and Hoseclips 

for Irrigation System 

IRRIGATE-TUBE-HF       Sterile High Flow Tubing and Hoseclips

for Irrigation System

1. Lift top of pump head and insert large diameter tubing.

Refer to diagram on irrigation pump housing to ensure
tubing is routed properly (smaller diameter tubing flows
towards Synthes Anspach handpiece housing).

2. Close lid on pump head.
3. Insert bayonet end of tubing into irrigation bag.

Caution:

Tubing can disconnect from connectors without

warning if occluded. DO NOT step on, set equipment on,
pinch, kink, clamp, or otherwise occlude tubing during use.

Irrigation Attachment Clip Assembly

Refer to “Ordering Information” section for part numbers.
1. Slide irrigation tubing onto proximal end of irrigation

attach ment clip.

2. Attach irrigation attachment clip to handpiece.
3. Secure tubing to handpiece hose using Hose Clips, which

are included with tubing.

‚

„

                                                                                                                             Anspach Electric Systems

Instructions for Use

      Synthes

         17

0x6.001.507_AD  13.06.14  11:12  Seite 17

Summary of Contents for Anspach















































Reviews:

No comments