manualshive.com logo in svg

Synthes Anspach, Instructions For Use Manual, Page: 15 / 46

Share
Download
Synthes Anspach Instructions For Use Manual Download Page 15

eMax 2 and eMax 2 Plus Operating Instructions

Note:

Depressing simultaneously the Irrigation Increase and

Decrease buttons will display the Console Software version
as a two digit number. 

For Example: XY this to be interpreted as Software Version
X.Y. 

On Consoles with no Irrigation (SC2102) the buttons are not
marked but are located in the same location which are de-
tectable by feel.

Irrigation

Increase/Decrease

Irrigation ON/OFF

Foot Control

LED: Foot
Control #2

LED: Foot
Control #1

Hand Control

R: Reverse

F: Forward

LED: Reverse

LED: Forward

H 

Decrease Speed

G

Increase Speed 

Operating Instructions

Upon startup, console is set to operate handpiece in forward
(clockwise when viewed from the proximal end of the
 Handpiece) direction at maximum speed and display reads
80,000 RPM. System operation, including optional  irrigation,
can be controlled from console face panel. On  applicable
consoles LED’s on face panel correspond to  connector ports
on connector panel. System operation can also be controlled
by several available foot control options and an optional
hand control.

Console Face Panel Operation

1. To increase or decrease speed of handpiece, depress blue

arrows located on console face panel. Speed increases
and decreases in 10,000 RPM increments. Each LED will
indicate the max RPM: 
10 = 10,000 RPM
20 = 20,000 RPM
30 = 30,000 RPM
40 = 40,000 RPM
50 = 50,000 RPM
60 = 60,000 RPM
70 = 70,000 RPM
80 = 80,000 RPM

2. To change direction, depress “R” or “F” arrow located 

on console face panel. Console beeps once, indicating
handpiece direction has changed. Direction can only be
changed when handpiece is not running. A series of three
beeps indicates console is set to operate handpiece in
 reverse/counterclockwise direction. LED on console face
panel located to left of “F” indicates forward direction.
LED located to left of “R” indicates reverse direction.

3. Optional: To activate irrigation, depress “Irrigation”

 button on face panel. LED illuminates. To control flow of
irrigation, depress arrows located to right of irrigation
 button on face panel.

14         

Synthes

      Anspach Electric Systems

Instructions for Use

0x6.001.507_AD  13.06.14  11:12  Seite 14

Summary of Contents for Anspach















































Reviews:

No comments