manualshive.com logo in svg

Synthes Anspach, Instructions For Use Manual, Page: 11 / 46

Share
Download
Synthes Anspach Instructions For Use Manual Download Page 11

CUTTER

RUN

ADJUST

TUBE

SAFE

F

F

R

Glossary of Symbols

10         

Synthes

      Anspach Electric Systems

Instructions for Use

Located on the Foot Pedal switch this
 indicates a change state (on/off) for the
 Console Irrigation System

Located on the Foot Pedal switch this
 indicates a change of rotational direction 
for the Handpiece

Located on the Handpiece this indicates
 position of the knurled knob to the desired
 location

Symbol with yellow background: CAUTION:
Refer to accompanying documentation

AC Power Source

Consult Operating Instructions

Located on the Console this indicates 
Motor or Handpiece unit

Located on the Console this indicates 
Foot Control activation

Located on the Console this indicates 
Hand Control activation

Located on the Console this indicates
 Forward (Clockwise rotation when looking at
Handpiece from proximal end)

Located on the Console this indicates Reverse
(Counterclockwise rotation when looking at
Handpiece from proximal end)

Revolution per Minute

Located on the Console this indicates a
change state (on/off) for the Console
 Irrigation System

Located on the Console this indicates a
change of irrigation rate for the Console
 Irrigation System

30 Sec ON /  Duty Cycle of the e12 system and DRIVER
30 Sec OFF

Company Logo

Direction of rotation

Direction of rotation for lock position

Indicates setting, position, or location

Indicates setting, position, or location

Indicates the drill tip exposure

Indicates the attachment setting, refer to
MA-D20 and MA-DRIVER section in this
document for further details

Indicates position or location

Indicates position or location

Indicates action of rotation and position for
Secure (LOCK) and Release (UNLOCK)

Direction of rotation

Direction of rotation for lock position

Direction of rotation

Located on the Foot Pedal switch this
 indicates a change of rotational direction
for the Handpiece

Located on the Foot Pedal switch this
 indicates a change state (on/off) for the
Console Irrigation System

0x6.001.507_AD  13.06.14  11:11  Seite 10

Summary of Contents for Anspach















































Reviews:

No comments