background image

Section I 

Warnings

006-0006205  

UPS-1500 Series 

Rev ZC 

6 of 60 

05/28/2019  

www.synqor.com

Section I 

Warnings

Battery Pack

The individual LITHIUM POLYMER BATTERIES contained in the SynQor battery pack are sealed units 

that are further mechanically protected by the battery pack’s chassis and electrically protected by 

the battery pack’s electronic circuitry.  Under normal conditions they do not pose a hazard, but 

they should not be physically, thermally or electrically abused.

The TRANSPORT of the battery pack must comply with applicable regulations of the locality.  See 

“Battery Pack - Handling the Battery Pack”.

The battery pack should be DISPOSED in accordance with applicable regulations of the locality 

or RETURNED to a factory-authorized Service Center. 

Emergency response contact information for battery damage, leaks, smoke, or fires can be found 

at the following link: 

http://www.SynQor.com/UPS/documents/Contact.pdf.

 Please contact 

the SynQor factory for all other questions regarding the UPS battery pack.

CAUTION: Do not dispose of batteries in a fire. The batteries may explode.

CAUTION: Do not open or mutilate batteries. Released electrolyte is harmful to the skin and 

eyes. It may be toxic.
Always use the proper SynQor battery pack.  See the battery replacement chart on page 45.

Protection from the Environment

The  SynQor  UPS  is  a  ruggedly  built  product  having  its  electronics  and  battery  contained  in 

sealed chambers.  It is capable of withstanding harsh levels of mechanical acceleration, shock 

and vibration, temperature and pressure variations, and exposure to water, salt, sand and dust 

within the levels specified in the data sheet.  THESE LEVELS SHOULD NOT BE EXCEEDED.
Do not obstruct the air intake in the front of the UPS or the fan exhausts in the rear panel of the 

UPS while the UPS is operating.

No User Serviceable Parts

The SynQor UPS has no user serviceable parts inside of it.  DO NOT REMOVE the cover of the 

UPS or any of its connectors.  DO NOT OPEN the battery pack.  Only factory trained personnel 

should perform repairs.

Summary of Contents for UPS-1500 Series





























































Reviews: