manualshive.com logo in svg

Synopsys DesignWare ARC AXC003, User Manual, Page: 57 / 145

Share
Download
Synopsys DesignWare ARC AXC003 User Manual Download Page 57

 

57 

Memories on the AXC003 CPU Card 

DesignWare ARC AXC003 CPU Card User Guide 

 

Version 6323-018 

Synopsys, Inc. 

 

 

May 2017 

Table 19 

Memory mapping for HS34 Emulation 

0xFFFF_FFFF 
0xF000_0000 

AXI2APB on AXC003 CPU Card (CREG) 

0xEFFF_FFFF 
0xE000_0000 

AXI2APB on Mainboard 

0xDFFF_FFFF 
0xD000_0000 

AXI Tunnel Slave for HAPS System 

0xCFFF_FFFF 
0xC000_0000 

DCCM 256k 

0xBFFF_FFFF 
0x8000_0000 

DDR3 SDRAM 

0x7FFF_FFFF 
0x4000_0000 

Unused 

0x3FFF_FFFF 
0x3000_0000 

Internal ROM 

0x2FFF_FFFF 
0x2000_0000 

SRAM on Mainboard 

0x1FFF_FFFF 
0x1000_0000 

ICCM 256k 

0x0FFF_FFFF 
0x0000_0000 

SRAM on AXC003 CPU Card 

For more booting information see ARC HS36 Booting from ICCM0 on page 73. 

To make proper builds of software for HS36 with CCM memories, the 

arc_hs34.tcf

 file is 

provided in the AXC003 software package. 

The GPIO pin located at SW2501[6] defines whether data cache and instruction cache are 
used. This pin does not change hardware configuration, and it is used by the pre-bootloader 
software. During initialization the pre-bootloader reads the value of this pin through CREG. If 
this bit is 

1

, data cache and instruction cache are enabled and the CPU operates as HS36. 

Otherwise the caches are disabled and CPU is in HS34 emulation mode. 

6.8 Memories on the AXC003 CPU Card 

The global memory is available on the AXC003 CPU Card: 

  2 GByte DDR3 SDRAM 

  256 KByte SRAM 

  32 KByte internal ROM 

The memory controller for the DDR3 SDRAM supports a single port.  

An  internal  ROM  controller  is  implemented  as  FPGA  RAM  blocks  initialized  with  a  pre-
bootloader code. This region is not intended to be used by application software.  

Additional  local  memories  (DCCM  and  ICCM0)  are  available  for  the  ARC  HS36  core;  see 

Main Features of the ARC Cores

 section on page 35. 

Summary of Contents for DesignWare ARC AXC003


















































































































































Reviews:

No comments