Installation
Caution:
Be sure to turn off hot and cold water supplies before
installing or servicing faucet.
Step 1
If installing model with hose and spray, install hose
guide into hole in sink (normally the far right hole on four
hole sink). From underneath sink place washer then nut over
hose guide and secure to sink. Insert hose through hose guide
and up through middle hole from left in sink. Loosely install
the anchor bar (KN-23), spacer (KN-26) and nut (L-36) on the
mounting bolts and place gasket on base of faucet. From above
sink attach hose securely to nipple on base of faucet.
Step 2
Align faucet to sink by matching underside arrow
and word “FRONT” on base plate (KN-33) with front of sink.
Without straightening copper supplies insert through center
hole of sink and anchor bar/spacer/nut assemblies through
holes in sink. Secure faucet to sink by tightening nuts from
underside. (If sink surface is uneven use putty or sealant to
make proper seal under base.)
Step 3
Carefully straighten copper supplies to avoid kinking
tubing. Connect hot supply to left tube and cold supply to right
tube using appropriate connectors.
Step 4
It is very important to thoroughly flush the supply
lines to prevent foreign matter, i.e. copper chips, sand, stones,
etc. from damaging the sealing surfaces of cartridge. Remove
aerator and turn valve handle on to full cold position, open cold
supply. Without closing, turn handle to full hot and open hot
supply. Let water run in hot only and cold only positions long
enough to flush supply lines thoroughly. If equipped with a hose
and spray, direct spray head into sink and activate spray. Shut
off faucet and replace aerator. Check for leaks.
Step 5
The handle limit stop can be set to limit handle turn
to the hot position. The limit mechanism is factory set to allow
full handle travel. To adjust the limit stop, turn handle to the
full hot position and lift handle to open faucet approximately
half way to obtain a smooth flow for correct initial temperature
measurement.
Step 6
If when faucet is on and in full hot position and water
is too hot, remove plug button (KN-157), loosen set screw
(L-22) and remove handle (KN-3RB or KN-3BRB), lift limit
stop ring using a small flat head screw driver and rotate counter
clockwise to lower temperature. If water is not hot enough,
rotate clockwise (See Figure 1 on reverse side). After correct
temperature is achieved, reattach handle, reversing procedure
above.
Cartridge Replacement (KN-4)
Step 1
Remove plug button (KN-157), loosen set screw (L-22)
and remove handle (KN-3RB or KN-3BRB).
Step 2
Engage tabs in cartridge wrench (LN-34) with slots in
compression ring (KN-2) and use screwdriver in wrench holes or
pliers on wrench and turn counter clockwise until compression
ring engages with cap (KN-1). Continue turning counter
clockwise so that cap/ring assembly is removed from the body
(KN-11).
Step 3
Remove cartridge and three ring seal (KN-4).
Step 4
Install new cartridge while taking care to maintain
position of the three ring seal at the base of the cartridge. Match
posts in base of cartridge with alignment holes in adapter plate
during assembly.
Step 5
Reassemble faucet in reverse fashion. Thread cap onto
body firmly by hand. Do not use a wrench which may damage
the finish. Tighten compression ring (KN-2) finger tight using
the wrench (LN-34) then 1/4 to 1/2 turn further. Set hot water
limit stop in accordance with installation step 6 above.
Diverter replacement (KN-169)
1. Follow cartridge replacement steps 1 through 5 above.
2. Remove retaining ring (K-44) with 3/8” hex key wrench.
3. Remove diverter (K-43) and o-ring (K-46).
4. Grease diverter o-ring and install into body.
5. Press diverter into o-ring and body.
6. Replace retaining ring.
Kitchen Faucet
S-23 Series
Installation and Service Instructions
Symmetrix
™
10-1/8"
257mm
7-1/2"
191mm
8"
203mm
7-1/4"
184mm
6"
152mm
6-1/4"
159mm
1/2"- 13mm
with spacer
1-1/4"- 32mm
without spacer
spacer
optional 1/2-14
NPT fitting
5 1/4
133mm
8-3/4"
222mm
10-7/8"
276mm
1/4-20" UNC
Dimensions
Symmetrix Kitchen Faucet, S-23
Note:
Dimensions subject to change without notice.