Symmetricom TimeProvider 500 series Reference Manual Download Page 41

Page: 41 / 165

Issue 2: Sep 99

TMSL 097-44018-26

Page 41

COMMAND CODE: ED-PORT

PURPOSE

EDIT PORT

This command modifies the priority, reference type, and signal type mode for a port.

INPUT FORMAT

ED-PORT:[<tid>]:<aid>:<ctag>::[<framing>],[<priority>],

[<reference type>],[<signal type>][,[<reference

condition>]];

Any parameter left blank causes no change to that parameter. The parameter values in the table below
are as follows:

= 1–2

= 1–11

= 1–2 or ALL

= 1–12 (1–10 for TOTA-5 & TOTA-M)

= 1–4 or ALL

= 1–10 (1–20 for EA20) or ALL

= 2–4 (c > b)

= 2–10 (2–20 for EA20) (h > g)

aid

parameter

value

meaning

DCIM-a-b

framing

CAS

channel associated signaling

CAS4

channel associated signaling with cyclic redundancy check 4

CRC4

common channel signaling with cyclic redundancy check 4

D4 framing

ESF

ESF framing

FAS

common channel signaling

priority

1–4

priority of the reference, 1 is highest priority

reference
type

(null)

(not applicable)

signal type

ANALOG

analog signal

DIGITAL

digital signal

reference
condition

ALW

this input reference can be used

INH

this input reference cannot be used (but can be IS-NR)

Summary of Contents for TimeProvider 500 series






































































































































































Search results

Summary of Contents for TimeProvider 500 series

Reviews:

Symmetricom TimeProvider 500 series, Reference Manual, Page: 41 / 165

Search results

Summary of Contents for TimeProvider 500 series

Reviews: