manualshive.com logo in svg

Symmetricom TimeProvider 2300, User Manual

Share
Download
Symmetricom TimeProvider 2300 User Manual Download Page 36

36

TimeProvider 2300/2700 User’s Guide

098-00564-000 Revision A3 – July, 2013

Chapter 1  Overview
Configuration Management

Configuration Management

The Command Line Interface (CLI), also called the ASCII command set, can be 
used to control the TimeProvider 2300/2700 from a terminal connected to the 
EIA-232 serial port, or the Ethernet MGMT port. Refer to 

Chapter 3, CLI Commands

 

for further details.

Web Interface for Status Information

The TP 2300/2700 also allows the user to access status information via the MGMT 
port using HTTP or HTTPS protocol. To use the TP 2300/2700 web interface, enter 
the MGMT port IP address into a web browser. Enter your user name and password 
for the TP 2300/2700 when prompted. See 

Figure 1-19

 for an example of the status 

screen that will appear. 

Note:

 Before you can communicate with the TimeProvider 2300/2700 

through an Ethernet connection, you must first configure the Ethernet 
port using the serial connection (see 

Provisioning the Ethernet 

Ports

, on page 189).

Summary of Contents for TimeProvider 2300



















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands