manualshive.com logo in svg

Symmetricom TimeHub 5500, User Manual

Share
Download
Symmetricom TimeHub 5500 User Manual Download Page 239

097-55501-01 Revision M – January 2009

TimeHub 5500 User’s Guide 239

Chapter 5  Maintaining the TimeHub 5500

Replacing Cards

Replacing the Output Driver Card

To replace the Output Driver card, follow the procedure below while referring to 

Figure 5-6

.

1. Put on a properly grounded ESD wrist strap.

2. Using a #2 Phillips-head or Pozidrive screwdriver, loosen the captive screws on 

the front panel.

3. Remove the card from the shelf.

4. Insert the replacement card into the shelf: ensure that the card aligns properly 

with its mating backplane connector; push the card into place until it is fully 
seated into the backplane connectors.

5. Wait for the Power LED to light, the DS1 and/or CC LEDs to light according to the 

Output Connector cards installed, and the Fail and Alarm LEDs to turn off.

6. Press the Cutoff pushbutton on the Management card several times.

7. Verify that any alarm conditions are cleared.

8. Tighten the captive screws at the top and bottom of the card.

Replacing the Management Card

When you replace an existing Management Card 090-55542-01 with a replacement 
Management Card, the newly-inserted Management Card may not immediately 
communicate via Ethernet. This could be mistakenly perceived as a Dead On 
Arrival unit due to communication failure.

The original IMC card installed in the TimeHub has a user-assigned IP address 
along with a hard-wired MAC address. This information is saved in the ARP table on 
the network router. When a new IMC card is plugged in, the network router starts 
querying the new IMC card for IP and MAC address information. Since the new IMC 
card has an initial IP address of “0.0.0.0”, certain routers consider this IP and MAC 
address to be harmful to the network and therefore disable the port associated with 
the new IMC card for a period of time. This lockout period can vary depending on 
the router’s configuration and can take up to 5 minutes to restore.

When a new IMC card is introduced to the network with the old IP address of the 
original IMC card, there is a transition period for the network router to associate the 
IP address with the new IMC card’s MAC address. The router must update the ARP 
table to reflect the change in the MAC address. While the network router is updating 
the ARP table, all Ethernet communications with the IMC card will result in failure. 
The time it takes to complete this update varies depending on the sophistication of 
the router.

Summary of Contents for TimeHub 5500





































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands