G
The lightning flash
with arrowhead
symbol within an equilateral triangle is
intended to alert the user of the presence
of uninsulated “dangerous voltage” within
the product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons. The exclamation
point within an equilateral triangle is
intended to alert the user of the presence
of important operating and maintenance
(servicing) instructions in the literature
accompanying the product (i.e. this Quick
Start Guide).
G
CAUTION:
To prevent electric shock, do
not use the polarized plug supplied with the
device with any extension cord, receptacle,
or other outlet unless the prongs can be
fully inserted.
G
Power Source:
This Symetrix hardware
uses a universal input supply that
automatically adjusts to the applied
voltage. Ensure that your AC mains voltage
is somewhere between 100-240 VAC,
50-60 Hz. Use only the power cord and
connector specified for the product and
your operating locale. A protective ground
connection, by way of the grounding
conductor in the power cord, is essential
for safe operation. The appliance inlet and
coupler shall remain readily operable once
the apparatus has been installed.
G
User Serviceable Parts:
There are no
user serviceable parts inside this Symetrix
product. In case of failure, customers
inside the U.S. should refer all servicing to
the Symetrix factory. Customers outside
the U.S. should refer all servicing to an
authorized Symetrix distributor. Distributor
contact information is available online at:
http://www.symetrix.co
.
AVIS:
NE PAS OUVRIR
Il ne se trouve a l’interieur aucune piece pourvant entre reparée l’usager.
SEE OWNERS MANUAL. VOIR CAHIER D’INSTRUCTIONS.
S’adresser a un reparateur compétent.
RISQUE DE CHOC ELECTRIQUE
No user serviceable parts inside. Refer servicing to qualified service personnel.
CAUTION
WARNING:
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR MOISTURE
DO NOT OPEN
RISK OF ELECTRIC SHOCK
Important Safety Instructions
!
Read these instructions.
@
Keep these instructions.
#
Heed all warnings.
$
Follow all instructions.
%
Do not use this apparatus near water. This
apparatus shall not be exposed to dripping
or splashing and no objects filled with
liquids, such as vases, shall be placed on
the apparatus.
^
Clean only with dry cloth.
&
Do not block any ventilation openings.
Install only in accordance with the
manufacturer’s instructions.
*
Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that
produce heat.
(
This apparatus shall be connected to
a mains socket outlet with a protective
earthing connection. Do not defeat
the safety purpose of the polarized or
grounding-type plug. A polarized plug has
two blades with one wider than the other.
A grounding type plug has two blades and
a third grounding prong. The wide blade
or the third prong are provided for your
safety. If the provided plug does not fit
into your outlet, consult an electrician for
replacement of the obsolete outlet.
BL
Ensure proper ESD control and grounding
when handling exposed I/O terminals.
BM
Protect the power cord from being walked
on or pinched particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
BN
Only use attachments/accessories
specified by the manufacturer.
BO
Use only with the cart, stand, tripod,
bracket, or table specified
by the manufacturer,
or sold with the
apparatus. When a cart is
used, use caution when
moving the cart/apparatus
combination to avoid injury from tip-over.
BP
Unplug this apparatus during lightning
storms or when unused for long periods of
time.
BQ
Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug cord
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or has
been dropped.
Note:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Modifications not expressly approved by the manufacturer could void the
user’s authority to operate the equipment under FCC rules.
Cet appariel numerique de la classe B respecte toutes les Exigences du
Reglement sur le materiel brouilleur du Canada.
The 2-line analog telephone interface card device is in compliance
with the Federal Communications Commission’s (FCC) Rules and
Regulations 47 CFR Part 68, and the Administrative Council on Terminal
Attachments (ACTA) – adopted technical criteria, TIA-968-B – Telephone
Terminal Equipment, Technical Requirements For Connection of Terminal
Equipment To The Telephone Network, August 2009 and TIA-1096.
The 2-line analog telephone interface card device meets the Industry
Canada technical specifications CS-03 Part I for terminal equipment and
related access arrangements intended for direct connection to analogue
wireline facilities and DC-01(E) for the declaration of conformity and
registration of terminal equipment. The Ringer Equivalence Number
(REN) is an indication of the maximum number of devices allowed to be
connected to a telephone interface. The REN for the Analog Telephone
Interface (ATI) card is two. The termination of an interface may consist of
any combination of devices subject only to the requirement that the sum
of the REN’s not exceed two per ATI card. Multiple ATI Cards may be
installed to increase the REN for a system.
1 of 4
QUICK START GUIDE:
I/O Expansion Card
www.symetrix.co
|
+1.425.778.7728
What Ships in the Box
• I/O card.
• Card bracket.
• 2 black 4-40 Phillips head screws.
• 3 stainless steel 4-40 Phillips head screws.
• 2 or 4 detachable three position 3.81 mm
terminal block connectors.
Note:
Terminal block connectors are not included
with the 2 Line Analog Telephone Interface Card,
2 Line VoIP Interface Card, or the USB Audio
Card.
• This Quick Start Guide.
What You Need to Provide
• Radius 12x8 EX, Radius AEC, Radius NX 4x4,
Radius NX 12x8, or Edge.
• Anti-static work station.
Getting Help
Composer, the Windows software that
configures Symetrix Dante Network Audio
hardware, includes a help file which acts as
a complete User’s Guide for both hardware
and software. If you have questions beyond
the scope of this Quick Start Guide, contact
our Customer Support Group in the following
ways:
Tel: +1.425.778.7728
6:00 am to 6:00 pm
Monday through Friday,
Pacific Time
Web:
Email:
Chat: http://symetrix.casengo.com/vip/
