Symbol MiniScan MS-804FZY Integration Manual Download Page 11

Page: 11 / 184

About This Manual

The

MS-804FZY and MS-904HS Integration Guide

provides general instructions for

mounting, setting up, and programming the MiniScan MS-804FZY and MS-904HS.

Note:

It is recommended that an opto-mechanical engineer perform an
opto-mechanical analysis prior to integration.

Chapter Descriptions

Topics covered in this guide are as follows:

•

Chapter 1, Introduction

provides an overview of the MS-804FZY and MS-904HS

scanners, and explains the theory of operation.

•

Chapter 2, Installation

describes the mechanical, electrical, optical and other

environments related to installing the MS-804FZY and MS-904HS scanners.

•

Chapter 3, MS-804FZY Specifications

provides the technical and scanning

specifications for the

MS-804FZY scanner

•

Chapter 4, MS-904HS Specifications

provides the technical and scanning

specifications for the

MS-904HS scanner

•

Chapter 5, Scanning

provides information on scanning and trigger modes.

•

Chapter 6, Maintenance and Troubleshooting

provides information on

maintaining and troubleshooting the MS-804FZY and MS-904HS scanners.

•

Chapter 7, Parameter Menus

describes the programmable parameters, provides

bar codes for programming, and hexadecimal equivalents for host download
programming.

•

Chapter 8, Simple Serial Interface (SSI)

describes scanner-specific updates to

the

Simple Serial Interface (SSI) Programmer’s Guide

Summary of Contents for MiniScan MS-804FZY

























































































































































































Search results

Summary of Contents for MiniScan MS-804FZY

Reviews:

Related manuals for MiniScan MS-804FZY

Brands by name

Popular brands

Symbol MiniScan MS-804FZY, Integration Manual

Search results

Summary of Contents for MiniScan MS-804FZY

Reviews:

Related manuals for MiniScan MS-804FZY

Brands by name

Popular brands