Operating elements
1
2
3
4
5
Location
• To optimize charging, place the solar panel
(3)
in a location exposed to maximum sunlight. Do not set up
the solar panel in the shade or under any cover.
• Do not install the product in the direct proximity of other light sources such as yard or street lights, other-
wise the product will not switch on automatically at nightfall.
• The product is suitable for use in unprotected outdoor areas. Do not submerge!
Installation
a) Motion detection sensor
5 m
100°
b) Mounting
This product comes with a wall mount kit and is designed to be mounted on wall.
When drilling or tightening screws, make sure there are no cables, wires, or pipes located un-
derneath the surface. Inadvertently drilling through electric cables can cause life-threatening
electric shock!
Check if the supplied screws are suitable for the mounting surface material. If in doubt consult a
professional.
1. Select a wall surface 2.5 - 3 m above ground level. According to three screw holes on the supplied wall
bracket, mark three spots on the wall.
2. Using a drill, bore three holes on the marked spots.
3. Correctly orientate the bracket: the side with up arrow indication faces outward and the bracket edge
indicated by up arrow direction faces up.
Then secure three supplied dowels into the three drilled holes, and secure three supplied screws into
the three dowels separately.
4. Attach the lamp case
(2)
onto the wall bracket.
Align the lamp case horizontally on the top of the bracket while ensuring the solar panel
(3)
faces up.
Then slide the lamp base
(4)
all the way into the grooves of the bracket.
To remove the lamp case from the bracket, simply slide the lamp case up out of the grooves of the
bracket.
Side with up arrow indication
Solar panel facing up
Solar charging
When using for the first time or after prolonged periods of low sunlight, you should fully recharge the battery.
• The product must be switched on for the battery to charge.
• Switch the product off before it gets dark to prevent the light from switching on and draining the battery.
• Switch the product back on after sunrise the next day to resume charging.
Operation
•
When light level is ≤10 lux (e.g.at nightfall), the LED light turns on automatically (1x LED on).
•
When the built-in motion sensor is triggered, the LED light gets brighter (5x LEDs on).
•
When the ambient light reaches a certain brightness level, the LED light will turn off.
a) Motion sensor
•
The motion detection will be activated when the light level is ≤10 lux.
•
When motion detection is activated, 5x LED will stay on for a short period after the motion stops. After
that, 1x LED stays on during darkness.
1 PIR sensor cover
2
Lamp case
3 Solar panel
4
Lamp base
5 ON/OFF switch
Motion detection:
• Works best when the subject
walks across the sensor.
• Does not work well behind
glass.
Operating Instructions
Solar Wall Light with PIR Sensor
Item No. 2338749
Intended use
The product is intended for use as decoration and is not suitable for domestic lighting. This product is wall
mounted and has an built-in PIR sensor. 5 LEDs serve as the illuminant. The light turns on automatically at
nightfall. All LEDs will stay on for a short period when the PIR sensor is triggered. The product is powered by
one battery that recharges via the integrated solar panel during the daylight hours.
The product has an IP44 ingress protection rating. It is splash proof and suitable for outdoor use. Do not
submerge!
For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use can
result in short circuits, fires or other hazards. Read the instructions carefully and store them in a safe place.
Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and prod
-
uct names are trademarks of their respective owners. All rights reserved.
Delivery content
•
Solar wall light with PIR sensor (1x rechargeable battery inserted)
• 1x wall bracket
• 3x screws
• 3x dowels
• Operating instructions
Up-to-date operating instructions
Download the latest operating instructions at www.conrad.com/downloads or scan the QR
code shown. Follow the instructions on the website.
Explanation of symbols
The symbol with the exclamation mark in the triangle is used to indicate important information in
these operating instructions. Always read this information carefully.
This product is constructed according to protection class III.
The arrow symbol indicates special information and advice on operation.
Safety instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
a) General information
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dangerous playing
material for children.
•
Protect the product from extreme temperatures, strong jolts, flammable gases, steam and
solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it
from any accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can dam-
age the product.
• Do not short circuit the battery terminals
• Consult an expert when in doubt about the operation, safety or connection of the product.
•
Maintenance, modifications and repairs must only be completed by a technician or an au
-
thorised repair centre.
•
If you have questions which remain unanswered by these operating instructions, contact our
technical support service or other technical personnel.
b) LED light
•
Attention, LED light:
-
Do not look directly into the LED light!
- Do not look into the beam directly or with optical instruments!
c) Rechargeable batteries
• Correct polarity must be observed while inserting the rechargeable battery.
• The rechargeable battery should be removed from the device if it is not used for a long period
of time to avoid damage through leaking. Leaking or damaged rechargeable batteries might
cause acid burns when in contact with skin, therefore use suitable protective gloves to handle
corrupted (rechargeable) batteries.
• Rechargeable batteries must be kept out of reach of children. Do not leave rechargeable bat-
teries lying around, as there is risk, that children or pets swallow them.
•
Rechargeable batteries must not be dismantled, short-circuited or thrown into fire. Never re
-
charge nonrechargeable batteries. There is a risk of explosion!
