12
Aton CL114 / Swisscom EN / A31008-M2402-F151-1-2X19 / Bali.fm / 13.07.2012
Te
mpla
te Bali, V
e
rsion
1, 16.0
2.2012
Deactivating the ringer for the current call
§Menu§
¤
Silent
¤
§OK§
Activating/deactivating music on hold
You can set that your external participant hears music in case of internal recall and during call transfer.
§Menu§
¤
P#Q5#1M
¤
The number for the current setting flashes:
0
= off;
1
= on
¤
enter number
¤
§OK§
.
Repeater mode
With a repeater, you can increase the range of your base station. You will need to activate repeater mode (
Repeater mode and
No Radiation
page 16) cancel each other out.
Resetting the handset
You can reset individual settings and changes that you have made. Entries in the directory, the calls list and the handset's
registration to the base station will be retained.
§Menu§
¤
q
Settings
¤
§§OK§§
¤
q
Handset
¤
§§OK§§
¤
q
Reset Handset
¤
§§OK§§
¤
Reset?
¤
§§OK§§
Restoring the base station
When restoring factory settings:
◆
Individual settings are reset.
◆
All lists are deleted.
◆
The
No Radiation
mode is deactivated.
The date and time are retained.
Resetting the base station via the menu
When resetting via the menu
◆
Handsets are still registered.
◆
The system PIN is not reset.
§Menu§
¤
q
Settings
¤
§OK§
¤
q
Base
¤
§OK§
¤
q
Base Reset
¤
§OK§
¤
Reset?
¤
§OK§
Resetting the base station using the key on the base station
When resetting the base station using the key on the base station
◆
All handsets are de-registered and
◆
The system PIN is reset to the original code
0000
.
Carry out the following steps:
Remove the mains cable from the base station. Hold down the
registration/paging key
on the base station (
page 1) and reconnect the power cable to the base station at the same time. Hold the key down
for at least 5 seconds.
Operating the base station on the PABX/router
Operating on the router
When operating on an analogue port of a router, you can reduce problems with
echoing
by activating the
XES Mode
page 16). If you have no problems with echoing, this function should be deactivated.
Operating on the PABX
The following settings are only necessary when your PABX requires them, see the user guide for your PABX.
When entering the digits, enter them
slowly
one after the other.
Changing the dialling mode
§Menu§
¤
P#Q5#1N
¤
The number for the set dialling mode flashes:
0
= touch tone dialling (DTMF);
1
= dial pulsing (DP)
¤
enter number
¤
§OK§
.
Setting recall
§Menu§
¤
P#Q5#1Q
¤
The number for the current recall flashes:
0
= 80 ms;
1
= 100 ms;
2
= 120 ms;
3
= 400 ms;
4
= 250 ms;
5
= 300 ms;
6
= 600 ms;
7
= 800 ms
¤
enter number
¤
§OK§
.
Changing pause after line seizure
You can set the length of the pause inserted between pressing the talk key
c
and sending the phone number.
§Menu§
¤
P#Q5#1L
¤
The number for the current pause length flashes:
1
= 1 sec.;
2
= 3 sec.;
3
= 7 sec.
¤
enter number
¤
§OK§
.
Changing the pause after the recall key
§Menu§
¤
P#Q5#12
¤
The number for the current pause length flashes:
1
= 800 ms;
2
= 1600 ms;
3
= 3200 ms
¤
enter number
¤
§OK§
.
