Swiss Timing OSB 14 Series Page 13 User Manual Download | Manualshive

Page: 13 / 21

background image

Swimming Starting Block / OSB 14

Version 1.4

3454.519.02

Page 9

4.6 Assembly of the RBD / intermediate plate and platform

When assembling the RBD / intermediate plate (3), insert the 5 screws/washers (A) and tighten
them with the 5 nuts/washers (B).

When assembling the platform (2), insert the 6 A4 conical screw M8 (4) and tighten them.

Figure 6

– Assembly RBD / intermediate plate and platform

«
...
11
12
13
14
15
...
»

Summary of Contents for OSB 14 Series






















Reviews:

No comments

Related manuals for OSB 14 Series

Brand: ABBA Pages: 3

Brand: Lifetime Pages: 32

Brand: Hudora Pages: 8

Brand: HAMPTON BAY Pages: 6

Brand: HAMPTON BAY Pages: 24

Brand: GABOR Pages: 16

LSP400 LED Series

Brand: WE-EF Pages: 4

Brand: NEBO Pages: 2

MONTI 5293101 Series

Brand: Trio Pages: 2

12x8FT Rectangular Trampoline

Brand: SPORTSPOWER Pages: 38

Brand: Knightsbridge Pages: 7

Brand: WAC Lighting Pages: 2

Brand: SportsPlay Equipment Pages: 2

Brand: HAMPTON BAY Pages: 13

HELLUX BLOCKFORM DB 171-8

Brand: Lunux Pages: 7

Trapezleuchte 143

Brand: Lunux Pages: 10

Boomerang Lacrosse Rebound Screen

Brand: ACELETIQS Pages: 9

Brand: OBI Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands