Quick Start Guide
Charging ProPoint
To charge your ProPoint Mouse:
1.
1.
2.
3.
Plug the USB Charger into a USB
port on your computer or into
a USB charging accessory.
2.
Dock the mouse onto the charger.
The battery LED will flash green while charging & stop flashing
once fully charged. The first 60 seconds of charging will give
up to one hour of use. A full charge can take up to 90
minutes, giving up to 2 weeks of use. To begin using the mouse,
move the switch on the underside to the
ON
position
Connecting ProPoint via Bluetooth
Once the mouse is fully charged, you can pair it to your
computer via Bluetooth. Remove the USB Charger/Receiver.
Leave the mouse
OFF
for the first steps.
1.
2.
3.
Remove any existing “
ProPoint
” entries
in the list by selecting it, then select
Remove
.
4.
5.
When “
ProPoint
” appears in the list of devices, click on it
to pair your mouse.
If does not appear, check that your system
supports Bluetooth 4.0 (or later) & that Bluetooth is enabled.
Please note that Windows 7 does not support Bluetooth 4.0,
however you can purchase a USB Receiver which will work on
Windows 7. Accessories can be purchased from the Swiftpoint
store (www.swiftpoint.com) & other approved outlets.
“
ProPoint
”
USB Charger/Receiver
Ensure Bluetooth is switched on, on your device.
Go to the Bluetooth device menu in your system settings
- Windows: Settings > Devices > Add Bluetooth device
- MacOS/iOS: System Preferences/Settings > Bluetooth
Plug
the USB Charger/receiver into your computer.
Charge
your mouse for at least 2 minutes before using.
Switch
On
using the switch on the bottom of the mouse.
For more tips & videos, visit
www.swiftpoint.com/600
Configuring ProPoint on PC/Mac
Open browser, click in URL box & type:
www.swiftpoint.com/download-propoint-drivers
Follow the on-screen instructions
1.
2.
Left-click (front)
Right-click (center)
Middle-click (rear)
Thumb grip
LED
Middle
fi
nger
grip
Scroll-wheel
Docking
point
Switch
Connecting ProPoint to iPad Applications
1.
2.
Launch your supported remote desktop app, & start
a
remote session.
Pair your ProPoint to your iPad over Bluetooth (see above).
6.
If you have a problem, switch the mouse
OFF
& try again
from step 1.
ProPoint Features
Connecting to more than one Bluetooth device
ProPoint can store pairings with up to three separate
Bluetooth devices.
When switched on, the mouse will first try to reconnect with
the most recently used device. If this cannot be found it will
try to connect to the next device in the list.
If two or more of ProPoint's current Bluetooth connections
are available nearby, you can swap between them by holding
the center button while switching
OFF
then
ON
again using
the On/Off switch.
While holding down the mouse front button, move the switch
on the underside of the mouse to
ON
. Release the front
button once the LED starts to flash orange.
If the button is held for more than 5 seconds, the mouse will not
pair via Bluetooth. The LED will flash green & the mouse will enter
USB Receiver (sold separately) pairing mode.
Connecting ProPoint via USB Receiver
To connect via the USB Charger/Receiver, plug the USB
Charger/Receiver into a port on your computer & move the
switch on the underside of the mouse from the
OFF
to the
ON
position. The mouse will automatically connect to your computer.
When not using the mouse for brief periods, dock the mouse
on the USB Charger so it maintains a charge.
The mouse should be fully charged periodically.
When not using the mouse for extended periods, move the
switch on the underside of the mouse to the
OFF
position.
IMPORTANT
Install the
SWIFTPOINT CONTROL PANEL
to configure
your ProPoint mouse to perform exactly as you want it to.
Set the cursor speed, scroll speed & direction, assign button
functionality & much more. The driver will be updated
periodically to add & improve functions.
