manualshive.com logo in svg

Svantek Shawcity SVAN 977C, User Manual, Page: 56 / 343

Share
Download
Svantek Shawcity SVAN 977C User Manual Download Page 56

 

56 

     SVAN 977C User Manual 

The 

Microphone

 compensation (microphone inner noise and thermal compensation) is switched on by default, 

however  it  is  possible  and  necessary  to  switch  it  off  for  electrical  measurements  (e.g.  laboratory  calibration 
measurements).

 

The 

Free Field 

and

 Diffuse Field 

positions are intended to compensate the instrument frequency response in 

the  free  field  or  diffuse  field  conditions.  The  microphone  supplied  with  SVAN  977C  is  designed  for  sound 
measurements in the free field conditions. The 

Free Field

 option means that the correction filter for the diffuse 

field conditions is switched off. 

The

 Windscreen 

compensation should be switched on if you use the 

SA 22

 windscreen. 

The

  Outdoor Environment

  and 

Outdoor Airport

  compensations  are  dedicated  for the  applications  with the 

use  of  the 

SA  277C

  outdoor  microphone  outdoor  kit  (usually  when  SVAN  977C  is  working  as  a  part  of  the 

SV 277 monitoring station). The characteristics of the outdoor filters depend on the dominating sound incidence 
angle: environmental monitoring (incidence angle 90 deg) or airport monitoring (incidence angle 0 deg).  

The frequency characteristics of all filters are given in Appendix C. 

 

Note: When using windscreen SA22 the Windscreen compensation 
filter must be switched on during windy conditions to maintain good 
tolerances margin of the SVAN 977C frequency response. 

 

 

Note:  For  the  free  filed  measurement  with  the  SA  277C  outdoor 
microphone kit the Environment or Airport compensation must be 
selected. 

 

 

 

4.6  S

ELECTING MEASUREMENT RANGE 

–

 

R

ANGE

 

The

 Range 

position

 

is used for selecting the 

measurement range of the instrument.  

The 

Range

 screen presents for the selected 

range:  Leq  linearity  range,  Leq  dynamic 
range and Peak range for 1 kHz. 

There  are  two  ranges  available: 

High

  and 

Low

. Default value: 

Low

. 

 

<ENT>

 

 

The 

detailed 

description 

of 

the 

measurement ranges parameters is given in 
Appendix C.  

The  values  of  ranges  in  sound  modes 
depend 

on 

the 

settings 

in 

the 

Compensation Filer

 screen (

path: <Menu> 

/  Measurement  /  Compensation Filter

)  and 

in both sound and vibration modes 

– on the 

calibration factor. 

    

►   

 

 

Summary of Contents for Shawcity SVAN 977C
























































































































































































































































































































































Reviews:

No comments