6A2-54 ENGINE MECHANICAL (M13 ENGINE)
Cam wear
Using a micrometer, measure cam height “a”. If measured height
underruns its limit, replace camshaft.
Cam height “a” of camshaft
Camshaft runout
Set camshaft between two “V” blocks, and measure its runout by
using a dial gauge.
If measured runout exceeds limit, replace camshaft.
Camshaft runout limit
: 0.10 mm (0.0039 in.)
Camshaft journal wear
Check camshaft journals and camshaft housings for pitting,
scratches, wear or damage.
If any malcondition is found, replace camshaft or cylinder head
with housing. Never replace cylinder head without replacing hous-
ings.
Check clearance by using gaging plastic. Checking procedure is
as follows.
1) Clean housings and camshaft journals.
2) Remove all tappets with shims.
3) Install camshafts to cylinder head.
4) Place a piece of gaging plastic to full width of journal of cam-
shaft (parallel to camshaft).
5) Install camshaft housing.
6) Tighten camshaft housing bolts in such order as indicated in
figure a little at a time till they are tightened to specified
torque.
Tightening torque
Camshaft housing bolt
(a): Tighten 11 N·m (1.1 kg-m, 8.0 lb-ft) by the specified
procedure.
Standard
Limit
Intake cam
44.929 – 45.089 mm
(1.769 – 1.775 in.)
44.80 mm
(1.764 in.)
Exhaust cam
44.399 – 44.559 mm
(1.748 – 1.754 in.)
44.28 mm
(1.743 in.)
NOTE:
Do not rotate camshaft while gaging plastic is installed.
“10” “9”
“2” “1”,(a) “6”
“5”
“14” “13”
“20”
“17”
“19”
“18”
“21”
“12” “11” “4”
“3”
“8”
“7”
“16” “15”
Summary of Contents for Wagon R Plus RB310
