Suzuki SWIFT RS415 2017 Service Manual Download Page 679

Page: 679 / 1257

Automatic Transmission: 5A-139

Countershaft Assembly Components

S4RS0A5106048

Countershaft Assembly Disassembly and
Reassembly

S4RS0A5106049

Disassembly

1) Remove countershaft LH bearing (1) and reduction

driven gear (2) at once by using special tool and
hydraulic press.

Special tool
(A): 09925–98221

2) Remove countershaft RH bearing (1) by using

special tools.

Special tool
(A): 09913–61510
(B): 09926–58010

Reassembly

1) Install new countershaft RH bearing (1) by using

special tool and hydraulic press.

Special tool
(A): 09913–84510

NOTE:
Replace countershaft RH bearing together
with bearing cup as a set.

2) Install reduction driven gear (1) with special tools

and hydraulic press.

Special tool
(A): 09913–84510
(B): 09925–88210

1. Countershaft RH bearing

5. Bearing cap

2. Countershaft

6. Countershaft bearing shim

3. Countershaft LH bearing

: Apply automatic transaxle fluid.

4. Reduction driven gear

: Do not reuse.

I2RH0B510209-

I2RH0B510210-

I2RH0B510211-

I2RH0B510212-

I2RH0B510213-

Summary of Contents for SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SWIFT RS415 2017

Reviews:

Related manuals for SWIFT RS415 2017

Brands by name

Popular brands

Suzuki SWIFT RS415 2017, Service Manual

Search results

Summary of Contents for SWIFT RS415 2017

Reviews:

Related manuals for SWIFT RS415 2017

Brands by name

Popular brands