Suzuki SWIFT RS415 2017 Service Manual Download Page 243 | Manualshive

Page: 243 / 1257

background image

Engine General Information and Diagnosis: 1A-195

Radiator cooling fan High Speed Control System Check

S4RS0A1104084

Wiring Diagram

Troubleshooting

WARNING:

Keep hands, tools, and clothing away from engine cooling fan to help prevent personal injury. This fan
is electric and can come on whether or not the engine is running. The fan can start automatically in
response to the ECT sensor with the ignition switch at the “ON” position.

NOTE:

• Before performed trouble shooting, be sure to read the “Precautions of ECM Circuit Inspection: ”.
• When measuring circuit voltage, resistance d/or pulse signal at ECM connector, connect the special

tool to ECM and/or the ECM connectors referring to “Inspection of ECM and Its Circuits: ”.

E23

C37

3

4

18

19

5

6

7

10

11

17

20

47 46

49

50

51

21

22

52

16

25

9

24

14
29

55

57

54 53

59

60

58

2

26

27

28

15
30

56

48

32 31

34

35

36

37

40

42

39 38

44

45

43

41

33

1

12

13

23

8

3

4

18

19

5

6

7

10

11

17

20

47 46

49

50

51

21

22

52

16

25

9

24

14
29

55

57

54 53

59

60

58

2

26

27

28

15
30

56

48

32 31

34

35

36

37

40

42

39 38

44

45

43

41

33

1

12

13

23

8

BLK/RED

BLK/RED

80A

BLK/YEL

BLK/YEL

BLK/YEL

BRN/WHT

12V

5V

5V

2

8

E23-1

E23-60

C37-58

C37-15
C37-30

BLK/ORN

BLK
BLK

BLK/RED

LT GRN

BLK/RED

E23-16

E23-46

L

+

L–

H–

H

+

BLU/RED

BLK

BLUWHT

BLK

BLU/BLK

BLU/RED

4

GRN

GRY

E23-48

LT GRN

ORN

C37-24

C37-55

1

3

5

6

7

9

10

I4RS0A110082-

1. Relay box

5. Radiator cooling fan relay No. 3

9. “FI” fuse

2. Main relay

6. Radiator cooling fan motor

10. “RDTR FAN” fuse

3. Radiator cooling fan relay No. 1

7. ECT sensor

4. Radiator cooling fan relay No. 2

8. ECM

«
...
241
242
243
244
245
...
»

Summary of Contents for SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SWIFT RS415 2017

Reference Series

Brand: OEM Audio Pages: 29

Brand: Metra Electronics Pages: 2

Brand: Whispbar Pages: 15

Fleetwood Brougham Sedan 1966

Brand: Cadillac Pages: 56

Brand: Thule Pages: 8

Brand: Honda Pages: 4

Brand: Pet Gear Pages: 4

Brand: ECS Electronics Pages: 14

2012 Patriot Series

Brand: Jeep Pages: 505

Brand: Toyota Pages: 277

Brand: Whispbar Pages: 42

Brand: OEM Audio Pages: 21

Brand: Discount Car Stereo Pages: 5

Brand: Honda Pages: 219

Brand: Outback Pages: 3

Brand: Axxess Pages: 16

Professional Series

Brand: Towing Products Pages: 5

Brand: Ford Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands